Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Understanding cohesive zone behaviour of blast furnace based on computed tomography flow modelling in a fused bed of ferrous and coke particles

CFD-DEM Study on the Synergistic Effect of Coke Consumption and Particle Dynamics in the Blast Furnace Raceway

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Numerical Investigation of the Limit of Coke Rate Reduction in an Ironmaking Blast Furnace (BF)

Study on the High-Temperature Interaction between Coke and Iron Ores with Different Layer Thicknesses

A numerical study on the softening process of iron ore particles in the cohesive zone of an experimental blast furnace using a coupled CFD-DEM method

Evolution of Coke Microstructure and Metallurgical Properties During Graphitization in a Blast Furnace

CFD-DEM Investigation on Pressure Drops of Heterogeneous Alternative-Layer Particle Beds for Low-Carbon Operating Blast Furnaces

Effect of Coke Rate and Basicity on Computed Tomography-Measured Pore Parameters and Effective Thermal Conductivity of Iron Ore Sinter

Computational Study of Hot Gas Injection (HGI) into an Ironmaking Blast Furnace (BF)

Effect of Coke Ratio on Pore Structure Evolution in the High-Temperature Zone of Sintering Bed

Characterization of pore structure and effective thermal conductivity of iron ore sinter using micro CT images

Interfacial Phenomenon and Marangoni Convection of Fe–C Melt on Coke Substrate under in Situ Observation

The evolution of pore structure during coke graphitization process in the blast furnace hearth

Computational Fluid Dynamics Study of the Flow and Thermochemical Behaviors of a Carbon Composite Briquette in an Ironmaking Blast Furnace

Dynamic analysis of liquid permeability in the dripping zone of blast furnace and reaction behavior at the slag-coke interface

Transient 3D CFD study of pulverised coal combustion and coke combustion in a blast furnace: Effect of blast conditions

High Resolution X-ray Microtomography for the Characterization of Pore Structure and Effective Thermal Conductivity of Iron Ore Sinter

Experimental Investigation on the Flame Front Resistance of Gas Channel Growth with Melt Formation in Iron Ore Sinter Beds

A comparative study of pellets, sinter and mixed ferrous burden behaviour under simulated blast furnace conditions

Evaluating the Permeability Properties of Green Bed in Iron Ore Sintering Using High Resolution X-ray Computed Tomography and Orthogonal Array Tests