Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

A numerical study on the softening process of iron ore particles in the cohesive zone of an experimental blast furnace using a coupled CFD-DEM method

CFD-DEM Study on the Synergistic Effect of Coke Consumption and Particle Dynamics in the Blast Furnace Raceway

CFD-DEM Investigation on Pressure Drops of Heterogeneous Alternative-Layer Particle Beds for Low-Carbon Operating Blast Furnaces

Analysis of the Influence of the Degree of Reduction of Iron Ore Materials on the Shape and Location of the Cohesion Zone in a Blast Furnace

Data-driven Soft Sensors in Blast Furnace Ironmaking:A Survey

Numerical Investigation of the Limit of Coke Rate Reduction in an Ironmaking Blast Furnace (BF)

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Measurement and Simulation Validation of DEM Parameters of Pellet, Sinter and Coke Particles

Investigation of the Testing Method of Softening–Melting Properties of Iron-Bearing Materials

Reliability Study of Super-Ellipsoid DEM in Representing the Packing Structure of Blast Furnace

Estimation of Iron Ore Pellet Softening in a Blast Furnace with Computational Thermodynamics

Direct reduction of iron-ore with hydrogen in fluidized beds: A coarse-grained CFD-DEM-IBM study

A Comparative Study of the Performance of Different Particle Models in Simulating Particle Charging and Burden Distribution in a Blast Furnace Within the DEM Framework

Understanding cohesive zone behaviour of blast furnace based on computed tomography flow modelling in a fused bed of ferrous and coke particles

Wetting and Spreading Behavior of Molten Iron in Contact with Graphite Substrate: Interfacial Effects

Investigating the Effect of the Iron Ore Pellet Addition on the Interaction Among Blast Furnace Burden in the Cohesive Zone

DEM-CFD investigation on the blast furnace raceway characteristics: Heat/mass transfer, dynamics and mechanisms

Relationship and Mechanism Analysis of Soft-Melt Dropping Properties and Primary-Slag Formation Behaviors of the Mixed Burden in Increasing Lump Ore Ratio

DEM simulation of powder phase movement in coke packed bed generated by scanning particles of a blast furnace

Increasing the Softening as well as Melting Behaviors for Iron Ore Materials within the Blast Furnace Cohesive Zone through the High-temperature Interactivity

Analysis of impact of mechanical degradation of iron ore pellets on gas flow in a direct reduction furnace using simulation