Abstract:High-entropy alloys (HEAs) of AlxCoCrFeNi (x = 0.2, 0.5, and 1) were created using the spark plasma sintering (SPS) method in conjunction with an aerosolized powder. Their microstructure and phase constituents were characterized by X-ray diffractometry, scanning electron microscopy, and projection electron microscopy. The tensile properties, hardness, compactness, and damping properties were also tested. The results showed that the crystal structure of AlxCoCrFeNi HEAs changed significantly with the Al content, from the original single face-centered cubic FCC phase (Al0.2CoCrFeNi) to an FCC + BCC + B2 structure (Al0.5CoCrFeNi), and then to FCC + BCC + B2 + Sigma (σ) phase structures (AlCoCrFeNi). Twin crystals with FCC structure were also observed in the TEM of AlCoCrFeNi. A chemical composition analysis showed that the crystal structure transformation was related to the segregation caused by the increase of Al element content. The hardness of the AlxCoCrFeNi HEAs increased with the Al content, and the hardness of AlCoCrFeNi reached the highest value of 585.4 HV. The tensile properties of the alloy showed a trend of increasing and then decreasing values with the increase in Al content. The yield strength, ultimate tensile strength, and elongation of the Al0.5CoCrFeNi alloy reached the highest values of 557.7 MPa, 954.4 MPa, and 32.2%, respectively. Moreover, the fracture mechanism of the Al0.2CoCrFeNi and Al0.5CoCrFeNi alloys was that of a typical ductile fracture, while for the AlCoCrFeNi alloy, it was that of a cleavage fracture. The compactness of the alloy increased with the Al content. The combination of the FCC + BCC + B2 phase resulted in the damping capacity of Al0.5CoCrFeNi alloy reaching 0.018 at the corresponding strain amplitude of 6 × 10−4.

Fabrication of high-strength dual FCC phase Co-Cr-Fe-Ni-Cu-Mo high entropy alloy by plasma arc additive manufacturing using a combined cable wire

Fabrication of bulk Al-Co-Cr-Fe-Ni high-entropy alloy using combined cable wire arc additive manufacturing (CCW-AAM): Microstructure and mechanical properties

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Investigation of Co-Cr-Fe-Mn-Ni Non-Equiatomic High-Entropy Alloy Fabricated by Wire Arc Additive Manufacturing

Realizing strength-ductility combination of Fe3.5Ni3.5Cr2MnAl0.7 high-entropy alloy via coherent dual-phase structure

Microstructure and mechanical properties of dual wire-arc additive manufactured Al-Co-Cr-Fe-Ni high entropy alloy

Strength-ductility balance of AlCoCrFeNi 2.1 eutectic high-entropy alloy via additive manufacturing

A Dual-Phase Fe-Co-Ni-Cr-Mn High Entropy Alloy Thin Film with Superior Strength and Corrosion-Resistance

Deformation behavior of high-entropy alloy system Al – Co – Cr – Fe – Ni achieved by wire-arc additive manufacturing

A great enhancement of both strength and plasticity in a dual-phase high-entropy alloy by multi-effects of high carbon addition

A novel Fe-rich Co-free high entropy alloys with low cost and excellent comprehensive mechanical properties

Fabrication of a strong and ductile FeCoCrNiMo0.3 high-entropy alloy with a micro-nano precipitate framework via laser powder bed fusion

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Triple-wire plasma-arc additive manufacturing of Al x -Cr-Fe-Ni medium-entropy alloys: Microstructure and mechanical properties

Additive manufacturing of in-situ strengthened dual-phase AlCoCuFeNi high-entropy alloy by selective electron beam melting

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

High-strength AlCoCrFeNi2.1 eutectic high entropy alloy with ultrafine lamella structure via additive manufacturing

New insight into tailorable eutectic high entropy alloys with remarkable strength–ductility synergy and ample shaping freedom fabricated using laser powder bed fusion

A novel complex-structure Co-free Cr-Fe-Ni-Al-Si-Ti-Cu high entropy alloy with outstanding mechanical properties in as-cast and cold-rolled states

Additively manufactured heterogeneous precipitation-strengthened high-entropy alloys with high strength and ductility

In-situ synthesis of Alx-Co-Cr-Ni high entropy alloys via twin-wire and arc additive manufacturing (T-WAAM): microstructure evolution and mechanical properties