Abstract:A new Powder-bed Arc Additive Manufacturing (PAAM) processing which includes on-line remelting of deposited material has been developed for the manufacturing of high entropy alloys (HEAs) based on an existing AlCoCrFeNi2.1 pseudo-eutectic system. The remelting process is typically applied in the arc melting process to improve the homogeneity of prepared material. We investigated the microstructure and mechanical properties of produced AlCoCrFeNi2.1 HEA after applying a remelting process (1, 3, and 6 times) on each deposited layer. The results show the formation of the pseudo-eutectic microstructure, which consists of relatively large columnar grains of the dominant FCC phase (similar to 90 wt%) and fine dendritic grains of the minor BCC phase (similar to 10 wt%). The applied layer-remelting process shows negligible effects on the phase fractions and their compositions, however, it significantly degraded the tensile strength and ductility of prepared alloys. Particularly, the ductility of the alloy reduced dramatically from about 27% after one time layer-remelting to only about 3% after 3 times layer remelting. This is rationalised by the significant localisation of thermally induced plasticity caused by repeated remelting of deposited material. We also show that this thermally induced plasticity leads to an increased amount of local misorientation in both constitute phases, which suggests an increased amount of stored dislocations in the microstructure. Despite the potentially strain hardening due to this accumulation of the thermally induced plasticity, the appreciable growth and constrained dendritic morphology of BCC grains that developed after remelting play a prevailing role on the materials strength, which limit the interfacial strengthening of the eutectic microstructure and consequently result in the loss of the tensile strength. The obtained results will assist in the further development and microstructure optimisation of novel HEAs using powder-based additive manufacturing processes.

Triple-wire plasma-arc additive manufacturing of Al x -Cr-Fe-Ni medium-entropy alloys: Microstructure and mechanical properties

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Enhancing the Strength of AlCrFeNi HEAs Via Tailoring Aluminum Content and Optimal Aging Treatment

In-situ synthesis of Alx-Co-Cr-Ni high entropy alloys via twin-wire and arc additive manufacturing (T-WAAM): microstructure evolution and mechanical properties

Powder plasma arc additive manufacturing of (AlTi) 2x (CoCrNi) 100–2x medium-entropy alloys: Microstructure evolution and mechanical properties

Fabrication of bulk Al-Co-Cr-Fe-Ni high-entropy alloy using combined cable wire arc additive manufacturing (CCW-AAM): Microstructure and mechanical properties

Effect of fabrication methods on microstructures, mechanical properties and strengthening mechanisms of Fe0.25CrNiAl medium-entropy alloy

Microstructure and Properties of Non-Equiatomic Ni10Cr6WFe9TiAlx High-Entropy Alloys Combined with High Strength and Toughness

Heterogeneous-structure-induced ultrahigh strength and ductility in a metastable dual-phase Fe60Cr15Ni16Al9 medium entropy alloy

On the Development of Pseudo-Eutectic AlCoCrFeNi2.1 High Entropy Alloy Using Powder-bed Arc Additive Manufacturing (PAAM) Process

Effects of Ti and Al Additions on Microstructure and Mechanical Properties of FeCrNi Medium Entropy Alloy Fabricated by Laser Powder Bed Fusion

Microstructure and mechanical properties of dual wire-arc additive manufactured Al-Co-Cr-Fe-Ni high entropy alloy

Exceptional strength-ductility synergy in additively manufactured (CoCrNi)90Al5Ti5 medium-entropy alloy by heat treatment

Microstructure and Mechanical Properties of Wire Arc Additively Manufactured MoNbTaWTi High Entropy Alloys

Investigation of Mechanical Properties and Wear Resistance of A2/B2 Type Medium-Entropy Alloy Matrix Reinforced with Tungsten Particles by In-Situ Reaction

Manufacturing of Ni-Co-Fe-Cr-Al-Ti High-Entropy Alloy Using Directed Energy Deposition and Evaluation of Its Microstructure, Tensile Strength, and Microhardness

Microstructure and Mechanical Properties of Medium-Entropy Alloys with a High-Density Η-D024 Phase

Fabrication of high-strength dual FCC phase Co-Cr-Fe-Ni-Cu-Mo high entropy alloy by plasma arc additive manufacturing using a combined cable wire

Microstructure and mechanical properties of twin wire and arc additive manufactured Ni3Al-based alloy

Effect of Al on Microstructure and Mechanical Properties of Cast CrCoNi Medium-Entropy Alloy

Microstructure and Mechanical Properties of Co-free Ni2FeCrW Medium-Entropy Alloys Reinforced by Coherent Precipitates