Abstract:The major disadvantage of reinforced concrete structure was multi cracks under loading, seriously affecting its normal performance, but using traditional repaired materials to strengthen reinforced concrete structures can bring some side-effects, such as higher carbon oxide and cost. Herein, this study successfully designed an eco-friendly geopolymer repaired composites developed by molybdenum tailings, ground granulated blast-furnace slag and coal gangue. Firstly, the fresh and harden properties of geopolymer repaired composites was systematically studied including water bleeding rate, fluidity, setting time, unconfined compressive strength and bonding strength. The micro performance of geopolymer repaired composites was analyzed via scanning electron microscopy, thermogravimetry-derivative thermogravimetry, X-ray diffraction and fourier transform infrared spectroscopy to give some new viewpoints for revealing the coupled geopolymerization mechanism of molybdenum tailings/coal gangue/ground granulated blast-furnace slag in geopolymer repaired composites. Meanwhile, the gray level of concrete contact surface is calculated. The results show that the properties of geopolymer repaired composites with 5% NaOH designed by 1:3 binder/sand, 0.5 w/c and 1:3 molybdenum tailings/ground granulated blast-furnace slag were optimal properties with 1.73% water bleeding rate, 192 mm fluidity, 58 min and 178 min the initial and final setting time, respectively, 21.443 MPa 28-d unconfined compressive strength and 2.642 MPa bonding strength. Excessive NaOH amount would inhibit the unconfined compressive strength and bonding strength of geopolymer repaired composites, while the increase of ground granulated blast-furnace slag would improve unconfined compressive strength and bonding strength. The primary hydration products of geopolymer repaired composites were C–S–H and C-A-S-H gels. Molybdenum tailings, coal gangue, and ground granulated blast-furnace slag showed an important synergistic effect, improving its geopolymerization reaction and strength. Besides, bonding strength of geopolymer repaired composites was highly correlated with unconfined compressive strength and fractal dimension of surface roughness. The relation coefficients are 0.92005 and 0.94006, respectively. With the higher the unconfined compressive strength of geopolymer repaired composites and the larger fractal dimension of the concrete contact surface, the bonding strength of geopolymer repaired composites is higher and the bond between geopolymer repaired composites and concrete is denser. The increase in the amount of NaOH and the increase in ground granulated blast-furnace slag have an increasing and decreasing trend on the carbon emissions of geopolymer repaired composites, respectively. The most obvious increasing and decreasing trends are that the carbon emissions of GRC increase from 66.41 kg CO 2 -e/m 3 to 96.28 kg CO 2 -e/m 3 and decrease from 79.81 kg CO 2 -e/m 3 to 76.37 kg CO 2 -e/m 3 . The increase in the amount of NaOH is the main reason for the increase in the carbon emissions of geopolymer repaired composites, while the increase in ground granulated blast-furnace slag helps to reduce the carbon emissions of geopolymer repaired composites. The carbon emission of geopolymer repaired composites was reduced by 75.08%–83.4% compared with traditional mortar. The 28-day per unit unconfined compressive strength carbon emission of the geopolymer repaired composites with the optimal mix is 46.63% lower than that of the traditional mortar. Overall, this study can provide new viewpoints and novel channels for converting solid waste, including molybdenum tailings and coal gangue, into green recycled construction materials, provide highly promising insight for designing green construction products and new ideas in the development of low-carbon remediation materials for environmental sustainability, contribute an important force to environmental protection, and promote the growth of economic benefits in the process.

Reaction mechanism and mechanical properties of geopolymer based on kaolinitic coal tailings

Drying shrinkage behavior of geopolymer mortar based on kaolinitic coal gangue

Activation Mechanism of Coal Gangue and Its Impact on the Properties of Geopolymers: A Review

Synthesis and Reaction Mechanism of Geopolymer Gels with Increasing Calcium Content: from Experiments to Molecular Dynamics Simulation

Study of Mechanical Properties and Durability of Alkali-Activated Coal Gangue-Slag Concrete

Mechanical properties and solidification mechanism of coal gangue-granulated blast furnace slag geopolymer stabilized engineering slurry

Mechanical activation of coal gasification slag for one-part geopolymer synthesis by alkali fusion and component additive method

Reuse of iron ore tailings in the production of geopolymer mortars

Microstructure Analysis and Effects of Single and Mixed Activators on Setting Time and Strength of Coal Gangue-Based Geopolymers

Reaction kinetics, mechanical properties, and microstructure of nano-modified recycled concrete fine powder/slag based geopolymers

Investigation of mechanical, microscopic, and leaching properties of coal-based solid waste geopolymer mortar activated by soda residue and phosphogypsum

Effect of Na + alkaline activation on the geopolymerization of a pure metakaolin at room temperature

Thermally-treated asbestos-cement wastes as supplementary precursor for geopolymeric binders: CO 2 emission and properties

Strength and microstructural analysis of geopolymer prepared with coal-based synthetic natural gas slag

Synthesis And Characterization Of Geopolymers From Coal Gangue, Fly Ash And Red Mud

Preparation and properties of geopolymer containing phosphoric acid-activated fly ash and mechanically-milled kaolinite: Experiments and density function theory

Synthesis and Performance Evaluation of Nano-Calcium Carbonate-Modified Geopolymers Incorporating Fly Ash and Manganese Slag: A Comprehensive Investigative Study

Influence of liquid-to-solid ratios on properties and microstructure of coal gasification slag-based one-part geopolymer

Geopolymerization kinetics of steel slag activated gasification coal fly ash: A case study for amorphous-rich slags

Experimental investigation on the mechanical performance and microscopic characterization of desulfurization gypsum-reinforced ternary geopolymer

Upcycling of molybdenum tailings, coal gangue and slag into sustainable repaired composites by geopolymerization technology: Workability, embodied carbon and mechanical-microstructural development