Abstract:Titanium aluminide (TiAl) alloys are promising high-temperature structural materials in the aerospace field. Additive manufacturing is a desirable process for fabricating TiAl alloys. In the process of wire arc additive manufacturing of TiAl alloys, Al-based and Ti-based wires were used as the feedstocks. However, it is hard to ensure the two different wires melt synchronously under the heat of one single arc, so the desired microstructures with gamma (TiAl) phase and alpha(2) (Ti3Al) phase are hard to obtain. A two-wire TOP-TIG-based additive manufacturing process for TiAl alloys is proposed in this paper. The Ti6Al4V wire and pure Al wire are used as the feedstocks. The Al wire is fed in TOP-TIG mode behind the molten pool, while the Ti6Al4V wire is fed in conventional TIG mode in front of the molten pool. The two wires melt synchronously in a broad range of parameters. The compositions of the component can be controlled by adjusting the two-wire feeding speeds. The main microstructures of the as-fabricated component contain alpha(2)/gamma lamellae colonies, equiaxed gamma grains, and alpha(2) grains. In the top and middle regions, when the Al content is 45 at.%, the structures are full alpha(2)/gamma lamellae; as the Al content increases to 50 at.%, some equiaxed gamma grains distribute at the grain boundaries; the component with 55 at.% Al content exhibits the structures consists of equiaxed gamma grains with snowflake-shaped alpha(2)/gamma lamellae colonies. In the bottom region, all components exhibit the coarse equiaxed alpha(2) grains with gamma laths. As the Al content increases, the alpha(2) phase decreases, but the gamma phase increases, and from the top region to the bottom region, the volume fraction of the alpha(2) increases by about 19.4 %. The hardness value of the top and bottom regions is higher, and the middle region exhibits the lowest hardness. As the Al content increases, the hardness decreases. The component with 50 at.% Al exhibits the highest compressive strength with 1762 MPa and the largest compressive ratio with 26.1%.

Welding materials for TIG welding, surfacing, and WAAM technology of titanium alloys

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

Wire Arc Additive Manufacturing with Novel Al-Mg-Si Filler Wire—Assessment of Weld Quality and Mechanical Properties

Microstructural Features and Microhardness of the Ti-6Al-4V Alloy Synthesized by Additive Plasma Wire Deposition Welding

Titanium Alloy Repair with Wire-Feed Electron Beam Additive Manufacturing Technology

Fabrication of Titanium Aluminide Alloys by Twin-Wire Tungsten Inert Gas Welding Applied with High-Frequency Induction Heating Wire Technology: Processing, Microstructure, and Properties

Wire Arc Additive Manufacturing of Titanium Aluminide Alloys Using Two-Wire TOP-TIG Welding: Processing, Microstructures, and Mechanical Properties

Welding of titanium and titanium alloys

Wire-arc Additive Manufacturing of TiB/Ti6Al4V Composites Using Ti-TiB2 Cored Wire: Processing, Microstructure and Mechanical Properties

Additive manufacturing and characterization of titanium wall used in nuclear application

Influence of oxygen content in the shielding gas chamber on mechanical properties and macroscopic structure of Ti-6Al-4V during wire arc additive manufacturing

Microstructure, Corrosion and Mechanical Properties of TiC Particles/Al-5Mg Composite Fillers for Tungsten Arc Welding of 5083 Aluminum Alloy

Layered synthesis of workpieces by mig-pulse surface method using austenitic metal-cored wire with nitrogen

Titanium alloy and stainless steel electron beam welding filler material, and preparation process and method thereof

Analysis of the Machining Process of Titanium Ti6Al-4V Parts Manufactured by Wire Arc Additive Manufacturing (WAAM)

Wire Arc Additive Manufacturing of Aluminum Foams Using TiH2-Laced Welding Wires

The State of the Art for Wire Arc Additive Manufacturing Process of Titanium Alloys for Aerospace Applications

Microstructure and Mechanical Properties of Wire Arc Additive Repairing Ti–5Al–2Sn–2Zr–4Mo–4Cr Titanium Alloy

Friction Stir Welding of Titanium Alloy using a Co-based Alloy Tool

A New Method for Refinement of Ti-6Al-4 V Prior-Β Grain Structure in the Alternating Magnetic Field Assisted Narrow Gap Gas Tungsten Arc Welding (AMF-GTAW) Via Filler Wire Oscillation

The Anisotropic Corrosion Behaviour of Wire Arc Additive Manufactured Ti-6Al-4V Alloy in 3.5% NaCl Solution