Abstract:Over the last 10 years, there have been significant developments in new devices for energy recovery, new membrane materials and new sizes and orientations of reverse osmosis (RO) plants, all designed to reduce costs and improve efficiency. The fundamental issue of keeping membrane surfaces clean to ensure efficient RO plant operation has seen relatively few recent developments. This is surprising as any fouling of the membrane surface will have a dramatic effect on energy consumption and plant efficiency. Many researchers have focused on identifying and studying the foulants in great detail, but there have been few studies in how to remove it. Commodity acid and alkali compounds are still widely used due to the perceived lower application costs. Specially blended cleaning chemicals incorporating detergents, surfactants and chelants are also in wide use and are increasingly accepted by the market to be economically and environmentally viable. “Strategically pairing chemical agents that have complementary cleaning mechanisms so a higher cleaning efficiency can be attained” has been described by Wui. The authors have established a research project to explore in detail the use of novel physical and chemical cleaning methods. These included effervescent chemicals, physically generated bubbles and high ionic strength cleaners designed to agitate the cake layer on the membrane surface, assisting deposit removal. A series of experiments using flat sheet test rigs and pilot plant have been completed and the results presented in papers at IDA Tianjin 2013. This paper explains how the multiple cleaning mechanisms remove foulants and presents new data from a food processing plant which recycles wastewater through an RO plant is presented. Historically, cleans were conducted every one to two weeks due to the very high fouling rate. An air inductor and specially formulated cleaning compound cleaners A & B incorporating effervescent and high ionic strength demonstrated that the plant could be cleaned more efficiently and in a shorter timescale than using conventional cleaners. The presence of microbubbles has a dramatic effect on cleaning efficiency as a result of agitation of deposits on the membrane surface. The differential pressure of the first-stage plant was reduced for 4.5 bar to consistently less than 1 bar. The quantity of permeate produced increased from 15 to 24 m3/h. The underlying fouling rate was dramatically reduced so cleans are now conducted on a 6–8 week cycle rather than a 10-day cycle. These improvements occurred because cleaning using microbubbles has been more effective and the membrane surface much cleaner than previously. A clean membrane surface does not foul as quickly as a dirty membrane surface due to surface roughness. The potential for enhanced membrane cleaning by combining different chemical and physical mechanisms is an exciting area of research.

Enhancing cleaning of microfiltration membranes fouled by food oily wastewater using microbubbles

Design and evaluation of microbubble-based cleaning process of membranes fouled by oily wastewater

Microbubble-Assisted Cleaning-in-Place Process for Ultrafiltration System and Its Environmental Performance

Influence of microbubble in physical cleaning of MF membrane process for wastewater reuse

Microbubble-Assisted Cleaning To Enhance the Removal of Milk Deposits from the Heat Transfer Surface

Washing performance of microbubbles on porous media

Microbubble RO membrane cleaning reduces fouling on WWRO plant

Enhanced Submerged Membrane Bioreactor Combined with Biosurfactant Rhamnolipids: Performance for Frying Oil Degradation and Membrane Fouling Reduction.

Application of biosurfactant rhamnolipid for cleaning of UF membranes

Optimizing fouling mitigation in membrane distillation by controlled microbubble size and concentration

Effective and low fouling oil/water separation by a novel hollow fiber membrane with both hydrophilic and oleophobic surface properties

In situ generated micro-bubbles enhanced membrane antifouling for separation of oil-in-water emulsion

Harnessing the potential of in-situ, electrically generated microbubbles via nickel foam for enhanced, low energy membrane fouling control

Continuation of a cleaning process: Application of MNBs-coagulation process to mitigate ultrafiltration membrane fouling

Research on the fouling and cleaning of micro-filtration membrane in oilfield wastewater

Cleaning Efficiency and Mechanism of Ozone Micro-Nano-bubbles on Ceramic Membrane Fouling

Effects of Online Chemical Cleaning on Removing Biofouling and Resilient Microbes in a Pilot Membrane Bioreactor

Characteristics of Membrane Fouling and Its Cleaning in Membrane Bioreactors for Water Purification

Surface Cleaning of Oil Contaminants Using Bulk Nanobubbles

Fouling and Cleaning of Microfiltration Membrane in Municipal Wastewater Reclamation.

A self-cleaning zwitterionic nanofibrous membrane for highly efficient oil-in-water separation