Abstract:Besides conventional structuring processes such as turning, milling or photo-chemical etching, laser processes are increasingly being used for surface structuring of metals. These laser processes differ fundamentally in that structuring is carried out either by material removal or by material redistribution. In this study, a new hybrid process of material ablation by means of pulsed laser radiation and material redistribution based on a remelting process by means of cw laser radiation is experimentally investigated. Besides an introduction to this new hybrid process, we give a detailed description of the equipment and methods used as well as surface structures produced on Ti6Al4V. A melt pool was generated on a prepared Ti6Al4V surface using cw laser radiation with a laser beam diameter of 520 mu m, laser power of 220 W, and a scanning velocity of 100 mm/s. In order to create surface structures, simultaneously, superimposed pulsed laser radiation with a laser beam diameter of 65 mu m, pulse duration of 60 ns, a maximum pulse energy of 0.35 mJ, and a pulse frequency of 50 kHz was used to evaporate small amounts of molten material from the melt pool. This localized evaporation of molten material is assumed to create vapor pressure that deforms the melt pool surface and therefore leads to surface structures. Our results indicate that by pulsed laser radiation capillary surface waves with a wavelength of the doubled laser beam diameter are excited on the melt pool surface. This forced excitation of capillary surface waves result in surface structures that are analyzed after solidification by means of white light interferometry. Based on this analysis we derived an oscillation frequency of v = 2.27 (+/- 0.16) kHz for the excited capillary surface wave as well as an effective kinematic viscosity of mu= 0.1328 cm(2)s(-1) for the damping of this surface oscillation during solidification. In terms of structural features, we achieved surface structures with heights of up to 100 mu m. Furthermore, structure height controllably scales in dependence on pulse energy and number of laser pulses as long as no ejection of molten material takes place. Finally, a comparison of the redistributed material volume per time shows that we achieved a volume redistribution rate of 28.37 mm(3)/min, which is significantly bigger than has been achieved with other laser texturing techniques so far and demonstrates the high potential of this new hybrid technique not only for surface structuring purposes.

Pin-Shaped Surface Structures Generated by Laser Single Pulse Drilling for High-Strength Interfaces in Thermally Joined Polymer–Metal Hybrids

Effect of Metal Surface Topography on the Interlaminar Shear and Tensile Strength of Aluminum/Polyamide 6 Polymer-Metal-Hybrids

Direct Bonding of Polymer and Metal with an Ultrahigh Strength: Laser Treatment and Mechanical Interlocking

Mechanism of laser-inducing hierarchical surface structures improving bonding strength of metal-plastic hybrids

Improving bonding strength of aluminium-PEEK hybrid metal-polymer joints by two-step laser surface treatment

Laser surface pre-treatment of aluminum for hybrid joints with glass fiber reinforced thermoplastics

Optimizing Hole Shape and Improving Surface Quality of Inconel 718 Alloy by High-Temperature Chemical Assisted Laser Processing

Binding Mechanisms Between Laser-Welded Polyamide-6.6 and Native Aluminum Oxide

Microconical surface structuring of aluminium tubes by femtosecond laser processing

Laser-assisted surface processing for functionalization of polymers on micro- and nano-scale

Experimental and numerical investigation on the strength of polymer-metal hybrid with laser assisted metal surface treatment

Improving the interfacial bonding strength and suppressing shrinkage porosity of 6061Al/GFRTP hot-pressing joints via interfacial modification

Combination of short and ultrashort pulse laser processing for productive large scale structuring of 3D plastic mould steel

Optimization of Laser Direct Structuring Process Parameters for Material Extrusion of Polycarbonate

Adhesion Enhancement of PEEK/6161-T6 FLJ Joints Via Laser Surface Modification

Surface treatment and solvent co-assisted easy direct bonding of polymer/metal

Influence of metal surface structures on composite formation during polymer‐metal‐joining based on reactive Al/Ni multilayer foil

Hybrid Laser Technique for Joining of Polymer and Titanium Alloy

Experimental Investigation on a New Hybrid Laser Process for Surface Structuring by Vapor Pressure on Ti6Al4V

Facile Fabrication of Functional PDMS Surfaces with Tunable Wettablity and High Adhesive Force Via Femtosecond Laser Textured Templating

Interface needle structure induced high-performance aluminum alloy/PPS hybrids