Abstract:It is a highly challenge to improve both the strength and electrical conductivity of Cu-Fe alloys (CFAs) simultaneously through the conventional casting method. In this work, one attempt has been conducted to overcome the dilemma via preparing CFAs with ultrafine alloy powders embedded by nano Fe particles. CFA powders with various Fe contents ranging from 5 wt.% to 50 wt.% were synthesized by a novel rapid solidification route named gas-water combined atomization (GWA) process. The GWA alloy powders were then processed by pressureless sintering and multi-pass rolling. The microstructure evolution, mechanical properties and electrical conductivity of CFAs manufactured were investigated in detail. The results showed that GWA alloy powders were nearly spherical, and the mass median diameter (D 50 ) is smaller than 10 μm. Inside the sintered alloy with full density, the average size of initial Fe particles and grains was smaller than 2 μm and 3 μm, respectively. Comparing to pure Cu without Fe particles, the grains of sintered CFAs were obviously refined by the Fe particles, the addition of Fe would increase the stacking fault energy of Cu alloy and inhibited the formation of Cu twins. After rolling, the Fe particles were elongated and fibrous along the rolling direction. The fibrosis degree of Fe particles was enhanced with the increase of Fe content. Cold-rolled CFAs with 5~50 wt.% Fe had the tensile strength of 560~1250 MPa and the conductivity of 33~65% IACS, which indicated that CFAs in this study achieved an optimal balance of mechanical and electrical properties. The microstructure evolution and strengthening mechanisms of CFAs by powder metallurgy (PM) and cold rolling were described. These findings can provide new insights for manufacturing PM CFAs with high performance.

CALPHAD-based design and preparation of high-strength, high-conductivity Cu–Fe–Zr alloys

CALPHAD-assisted composition and processing design of high-strength and high-conductivity copper alloy

High strength, high conductivity and good softening resistance Cu-Fe-Ti alloy

Achieving high strength and high conductivity synergy through hierarchical precipitation stimulated structural heterogeneities in a Cu-Ag-Zr alloy

Excellent Combination of Strength, Conductivity and Ductility Realized in a Dilute Cu-Cr-Zr Alloy by Coherent Nanoprecipitates

A novel precipitation‐strengthened conductive copper alloy: Cu‐Hf‐Si alloy

Microstructure and properties of high strength, high conductivity Cu-2.5Fe-0.3Cr-0.3Mg-0.2Si-0.1Ca-0.1Zr alloy treated by multi-stage thermomechanical treatment

CALPHAD aided design of high entropy alloy to achieve high strength via precipitate strengthening

Precipitation behavior and microstructural evolution during thermo-mechanical processing of precipitation hardened Cu-Hf based alloys

Significantly enhanced high-temperature mechanical properties of Cu-Cr-Zn-Zr-Si alloy with stable second phases and grain boundaries

Recent development of advanced precipitation-strengthened Cu alloys with high strength and conductivity: A review

A High Strength and High Conductivity Cu0.4Cr0.3Zr Alloy Prepared by Cryo-ECAP and Heat Treatment

A promising structure for fabricating high strength and high electrical conductivity copper alloys

Optimizing mechanical and electrical properties of Cu–3Zr alloy by thermomechanical processing

Ultra-high strength Al-Zn-Mg-Cu alloys with high zinc content prepared via powder hot extrusion

Microstructure and properties of Cu-50Fe alloy produced by chemical co-precipitation and powder metallurgy

Designing Ultrastrong and Thermally Stable FeCrAl Alloys with the Fine-Grained Structure

Achieving High Strength and High Electrical Conductivity in a CuCrZr Alloy Using Equal-Channel Angular Pressing

High Strength and High Electrical Conductivity in Cu-Fe Alloys with Nano and Micro Fe Particles

Synergistic strengthening effects of precipitation and work hardening in cold-rolled Cu-0.4 wt%Cr alloy

Effect of Zn on Precipitation Evolution and Mechanical Properties of a High Strength Cast Al-Li-Cu Alloy