Wear Problems of High-Speed Wheel/Rail Systems: Observations, Causes, and Countermeasures in China

Wanming Zhai,Xuesong Jin,Zenfeng Wen,Xin Zhao

DOI: https://doi.org/10.1115/1.4048897

IF: 14.3

2020-11-01

Applied Mechanics Reviews

Abstract:Abstract Wear problems of wheel/rail systems occurring on the Chinese high-speed railway network in the last decade are summarized and explained together with the corresponding experience of treating them. Focus is placed on uneven wear because even wear is not an urgent issue due to its very low wear rate for the Chinese high-speed railway systems. Two typical problems of longitudinal uneven wear, namely, wheel polygonization and rail corrugation, are introduced in terms of their characteristics, consequences, causes and initiation mechanisms. Next, wheel hollow wear and flange/gauge side wear, as typical problems of lateral uneven wear, are similarly discussed. Validated countermeasures against all these problems are presented at the end of this paper together with further proposals under testing or consideration. This work is principally based on first-hand data collected from field observations, monitoring tests and dynamic measurements, but typical numerical approaches and results are also presented to help explain the observed phenomena.

mechanics

What problem does this paper attempt to address?

This paper aims to solve the wear problem of the wheel - rail system in China's high - speed railway system, especially the non - uniform wear problem. The following are the specific problems that the paper attempts to solve:

1. **Summarize and explain the wheel - rail wear phenomena in the past ten years**:
- The paper summarizes the wear phenomena of the wheel - rail system that occurred on China's high - speed railways in the past ten years and explains them in combination with practical experience.
- The focus is on non - uniform wear because for China's high - speed railway system, the rate of uniform wear is very low and is not an urgent problem.

2. **Introduce typical longitudinal non - uniform wear problems**:
- Specifically introduce two typical longitudinal non - uniform wear problems: wheel polygonization and rail corrugation.
- Elaborate on the characteristics, consequences, causes and initiation mechanisms of these problems.

3. **Discuss lateral non - uniform wear problems**:
- Discuss wheel hollow wear and flange/gauge side wear as typical lateral non - uniform wear problems.
- Similarly, analyze the characteristics, consequences, causes and initiation mechanisms of these problems.

4. **Propose effective countermeasures**:
- Propose effective countermeasures for all the above - mentioned problems and introduce further suggestions that are being tested or considered.

5. **Research methods based on field observation and monitoring data**:
- The research is mainly based on first - hand data collected from field observations, monitoring tests and dynamic measurements.
- At the same time, typical numerical methods and results are also presented to help explain the observed phenomena.

### Formula and symbol explanations
Some of the formulas involved in the paper are as follows:

- The calculation formula for the vertical wheel - rail contact force \( F_N \) is:
\[
F_N=\frac{1}{G}\left(\frac{dZ}{18}\right)^{3 / 2}
\]
where \( G \) is an empirical constant with the unit of \( \text{m/N}^{2/3} \), and the recommended value is:
\[
G = 3.86\times r^{- 0.115}\times10^8
\]
where \( r \) is the rolling radius of the wheel with the unit of meter (m).

- The elastic compression \( dZ(t) \) is defined as:
\[
dZ(t)=Z_w(t)-Z_r(t)-Z_0(t)
\]
where \( Z_w(t) \) and \( Z_r(t) \) are the vertical displacements of the wheel and the rail respectively, and \( Z_0(t) \) is the irregularity including the geometry of wheel polygonization or rail corrugation.

- The tangential creep rate \( n \) is defined as:
\[
n=\frac{xr - v}{xr + v}
\]
where \( v \) is the translational speed of the wheel with the unit of m/s; \( x \) is the angular speed of the wheel with the unit of rad/s.

Through these studies, the authors hope to provide a comprehensive understanding of the non - uniform wear problem of the high - speed railway wheel - rail system and provide a scientific basis for future maintenance and improvement.