Abstract:Super-knock has been a significant obstacle for the development of highly turbocharged (downsized) gasoline engines with spark ignition, due to the catastrophic damage super-knock can cause to the engine. According to previous research by the authors, one combustion process leading to super-knock may be described as hot-spot induced pre-ignition followed by deflagration which can induce detonation from another hot spot followed by high pressure oscillation. The sources of the hot spots which lead to pre-ignition (including oil films, deposits, gas-dynamics, etc.) may occur sporadically, which leads to super-knock occurring randomly at practical engine operating conditions. In this study, a spark plasma was used to induce preignition and the correlation between super-knock combustion and the thermodynamic state of the reactant mixture was investigated in a four-cylinder production gasoline engine. The engine experiments were complemented by rapid compression machine (RCM) experiments of iso-octane and air which also used a spark plasma to investigate the fundamental physical and chemical mechanisms of super-knock. For the engine experiments, at low-speed high-load conditions, early spark timing was used to systematically induce preignition in the range of spark timing from 8 to -50 degrees CA ATDC in increments of 3 degrees CA. The intake pressure of the fresh air charge was set at 1, 1.3, 1.6 and 1.9 bar, and for each intake air pressure, the intake temperature was set at 20 and 60 degrees C. The results show early spark ignition could be used to trigger pre-ignition and to induce super-knock when the mixture thermodynamic state was above a critical condition. At a constant air temperature and high intake pressure, advancing the spark timing caused transitions from normal combustion to knocking conditions, to super-knocking conditions and then back to knocking conditions and to normal combustion. The transition between knocking conditions was well correlated with the thermodynamic state at the start of the in-cylinder pressure oscillations associated with knock. At a constant temperature and naturally aspirated conditions, no matter how advanced the spark timing was, only slight knock was observed, which indicates the thermodynamic state dominates the determination of knocking or non-knocking conditions. An energy density-pressure-temperature (E-P-T) diagram was developed to define super-knock, knock and normal combustion criteria. For the RCM experiments using isooctane at stoichiometric conditions with air dilution, a spark plasma was used to simulate pre-ignition. Three compression ratios were used to create different end of compression (EOC) temperatures. For each T EOC, with increasing EOC pressure, the combustion process also transitioned from normal combustion with flame propagation, to sequential end-gas auto-ignition with pressure oscillations and then to detonation with severe pressure oscillations. The combustion processes observed in the RCM experiments and the thermodynamic states were similar to the state conditions at the start of the pressure oscillations of the constant temperature and high intake pressure engine experiments. The results indicate RCM studies can be used to investigate the physical and chemical mechanisms of super-knock and E-P-T diagrams can be used to predict and distinguish super-knock from other combustion modes.

Implementation and Parameter Analysis of the Knock Phenomenon of a Marine Dual-Fuel Engine Based on a Two-Zone Combustion Model

Knock Prediction for Dual Fuel Engines by Using a Simplified Combustion Model.

Numerical investigation on knock characteristics and mechanism of large-bore natural gas dual-fuel marine engine

Numerical modeling of knocking combustion in spark ignition engines

Progress in knock combustion modeling of spark ignition engines

Experimental investigation of knock control criterion considering power output loss for a PFI SI methanol marine engine

Numerical Modeling of the Propagating Flame and Knock Occurrence in Spark-Ignition Engines

Three-Dimensional Computational Fluid Dynamics Modeling of the Combustion Process of a MAN L21/31 Marine Diesel Engine

An experimental study of knock analysis of HCNG fueled SI engine by different methods and prediction of knock intensity by particle swarm optimization-support vector machine

Experimental and model-based analysis of combustion and auto-ignition of gasoline and three surrogate fuels in a single-cylinder research engine operated under knocking conditions

An exploratory study of knock intensity in a large-bore heavy-duty methanol engine

Statistical Quantification of Knock With Spark Ignition and Pre-Chamber Jet Ignition in a Light Duty Gasoline Engine

Knock Prediction Improvement with Application to the Analysis of Knock Mitigation with Targeted Water Injection in SI Engines

Comparative Knock Analysis of HCNG Fueled Spark Ignition Engine Using Different Heat Transfer Models and Prediction of Knock Intensity by Artificial Neural Network Fitting Tool

Knock combustion characteristics of an opposed‐piston two‐stroke gasoline engine

Research on Performance Matching of Intake and Exhaust Ports of Marine Medium Speed Dual Fuel Engine

A Generalized Kinetic Model with Variable Octane Number for Engine Knock Prediction

An experimental study of knock in a DI hydrogen engine: The synergistic effects of the deep Miller cycle and oxygen-enriched atmosphere

Pressure Oscillation and Chemical Kinetics Coupling During Knock Processes in Gasoline Engine Combustion

Highly Turbocharged Gasoline Engine and Rapid Compression Machine Studies of Super-Knock

Effects of Chamber Geometry, Hydrogen Ratio and EGR Ratio on the Combustion Process and Knocking Characters of a HCNG Engine at the Stoichiometric Condition