Abstract:A series of high molar mass terpolymers is synthesized by ring-opening polymerization of L-lactide (LLA), 1, 3-trimethylene carbonate (TMC) and glycolide (GA). A totally bioresorbable composite is obtained by reinforcing a terpolymer matrix with plasma treated poly (L-lactide-co-glycolide) (PLGA) short fibers. Solution cast films of the various materials are allowed to degrade at 37 C at pH 8.5 Tris buffer using proteinase K, in comparison with a PLLA-TMC copolymer and a PLLA homopolymer. Degradation is monitored by using various analytical techniques such as gravimetry, DSC, GPC, H-1 NMR and SEM. The results show that the enzymatic degradation rate of PLLA-TMC-GA terpolymers with predominant LLA component is affected by both the average LLA block length (I-LLA) and crystallinity. A shorter average LLA block length results in lower crystallinity, which will lead to faster degradation. However, too short average LLA block length (i.e. I-LIA <= 4.0) can retard the degradation process. The composition of the copolymers remains unchanged during degradation. In contrast, the molar mass decreases due to hydrolytic chain cleavage in the bulk. Similarly, thermal property changes are observed with increase of the melting temperature and melting enthalpy in most cases. SEM observation strongly supports a surface erosion mechanism. The composite PLTG95/5/5C exhibits lower mass loss rate as compared to neat PLTG95/5/5 due to the presence of PLGA fibers which are non-degradable by proteinase K. On the other hand, the composite shows much faster molar mass loss rate than PLTG95/5/5 because the rapid hydrolytic degradation of PLGA fibers speeds up the degradation of the matrix by internal autocatalysis. (C) 2014 Elsevier Ltd. All rights reserved.

Depolymerization and Etching of Poly(lactic acid) via TiCl 4 Vapor Phase Infiltration

Dealkylation of Poly(methyl methacrylate) by TiCl 4 Vapor Phase Infiltration (VPI) and the Resulting Chemical and Thermophysical Properties of the Hybrid Material

TiCl4 Immobilized on a Composite Support SiO2/MgCl2·x(1,4‐butanediol)/poly[styrene‐co‐(acrylic Acid)] for Ethylene Polymerization: the Barrier Effect of Poly[styrene‐co‐(acrylic Acid)]

Diffusion Behavior and Kinetics for the Vapor Phase Infiltration of Trimethylaluminum in Poly(ethylene oxide): An In Situ Quartz Crystal Microgravimetry Study

Argon nonthermal plasma etching of poly(L-lactic acid) films: Tunning the local surface degradation and hydrolytic degradation rate

In Vitro and in Vivo Degradation Behavior of Poly(Trimethylene Carbonate-Co-D, L-Lactic Acid) Copolymer

Hydrolytic degradation of glycolide/L-lactide/ɛ-caprolactone terpolymers initiated by zirconium(IV) acetylacetonate

Photoinduced Degradation of Polymer Films Using Polyglyoxylate-Polyester Blends and Copolymers

Bulk Depolymerization of PMMA via Pendent Group Activation

Polymerization of vinyl chloride catalyzed by a titanium complex with an anionic oxygen tripod ligand

Hydrolytic Degradation of Glycolide/l‐lactide/ε‐caprolactone Terpolymers Initiated by Zirconium(iv) Acetylacetonate

Transformation of poly(L-lactide) crystals composed of linear chains into crystals composed of cycles

Bulk Depolymerization of Methacrylate Polymers via Pendent Group Activation

Morphological Investigation on Melt Crystallized Polylactide Homo‐ and Stereocopolymers by Enzymatic Degradation with Proteinase K

The effect of chemical composition on the degradation kinetics of high molecular weight poly(trimethylene carbonate-co-L-lactide)

Enzyme-catalyzed Degradation of Poly(l-Lactide)/poly(ɛ-caprolactone) Diblock, Triblock and Four-Armed Copolymers

Enhancing the Hydrolytic Stability of Poly(lactic acid) Using Novel Stabilizer Combinations

Enzyme-catalyzed Degradation Behavior of L-Lactide/trimethylene Carbonate/glycolide Terpolymers and Their Composites with Poly(l-Lactide-co-glycolide) Fibers

The Effect of the Surface Treatment on TiO2 Particles When Used as a Filler on Crystallization and Mechanical Properties of Polylactic Acid Composites. Case of Study: Silane Coupling Agents and Dicarboxylic Acids Were Used as Surface Modifiers

In vitro enzymatic degradation of the PTMC/cross-linked PEGDA blends

Depolymerisation of Poly(Lactide) Under Continuous Flow Conditions