Abstract:Objective: Formulate experimental adhesives containing titanium dioxide nanotubes (nt-TiO2) or titanium dioxide nanotubes with a triazine-methacrylate monomer (nt-TiO2:TAT) and evaluate the effect of these fillers on the physical, chemical, and biological properties of the adhesives. Methods: First, nt-TiO2 were synthesized via a hydrothermal method. The nt-TiO2 were mixed with a triazine-methacrylate monomer (TAT) to formulate nt-TiO2:TAT, which were characterized by transmission electron microscopy (TEM). The nt-TiO2, TAT, and nt-TiO2:TAT were evaluated via Fourier Transform Infrared, Ultraviolet-visible, and micro-Raman spectroscopies. An experimental adhesive resin was formulated with bisphenol A glycerolate dimethacrylates, 2-hydroxyethyl methacrylate, and photoinitiator/co-initiator system. nt-TiO2 or nt-TiO2:TAT were incorporated at 2.5 wt.% and 5 wt.% in the adhesive. The base resin without nt-TiO2 or nt-TiO2:TAT was used as a control group. The adhesives were evaluated for antibacterial activity, cytotoxicity, polymerization kinetics, degree of conversion (DC), Knoop hardness, softening in solvent (ΔKHN%), ultimate tensile strength (UTS), 24 h- and 1 year- microtensile bond strength (μ-TBS). Results: TEM confirmed the nanotubular morphology of TiO2. FTIR, UV-vis, and micro-Raman analyses showed the characteristic peaks of each material, indicating the impregnation of TAT in the nt-TiO2. Adhesives with nt-TiO2:TAT showed antimicrobial activity against biofilm formation compared to control (p < 0.05), without differences in the viability of planktonic bacteria (p > 0.05). All groups showed high percentages of pulp cell viability. The polymerization kinetics varied among groups, but all presented DC above 50%. The addition of 5 wt.% of nt-TiO2 and both groups containing nt-TiO2:TAT showed higher values of Knoop hardness compared to the control (p < 0.05). The groups with nt-TiO2:TAT presented lower ΔKHN% (p < 0.05) and higher UTS (p < 0.05) than the control group. After one year, the group with 5 wt.% of nt-TiO2, as well as both groups containing nt-TiO2:TAT, showed higher μ-TBS than the control (p < 0.05). Significance: The mixing of a triazine-methacrylate monomer with the nt-TiO2 generated a filler that improved the physicochemical properties of the adhesive resins and provided antibacterial activity, which could assist in preventing carious lesions around tooth-resin interfaces. The set of physical, chemical, and biological properties of the formulated polymer, together with the greater stability of the bond strength over time, make nt-TiO2:TAT a promising filler for dental adhesive resins.

The Effect of the Surface Treatment on TiO2 Particles When Used as a Filler on Crystallization and Mechanical Properties of Polylactic Acid Composites. Case of Study: Silane Coupling Agents and Dicarboxylic Acids Were Used as Surface Modifiers

Improvement in the physicochemical properties of titanium dioxide by surface modification with 1H-1-carboxylate of isopropyl-imidazole and 3-aminopropyltrimethoxysilane: case study—as a filler in polylactic acid composites

Effect Of Surface Modification Of Titanium Dioxide On The Uv-C Aging Behavior Of Silicone Rubber

New Insights into the Application of Biocompatible (Un)Modified TiO2 and TiO2-ZrO2 Oxide Fillers in Light-Curing Materials

Water-mediated chelation dynamics of dicarboxylic acid functionalized TiO2 nanoparticles for β-nucleation enhancement in isotactic polypropylene composites

Structure and Properties of Polylactide Composites with TiO2–Lignin Hybrid Fillers

Synergic Effect of TiO2 Filler on the Mechanical Properties of Polymer Nanocomposites

Synergistic effect of TiO2 nanoparticles and poly (ethylene-co-vinyl acetate) on the morphology and crystallization behavior of polylactic acid

Enhancing Dielectric Properties, Thermal Conductivity, and Mechanical Properties of Poly(lactic acid)–Thermoplastic Polyurethane Blend Composites by Using a SiC–BaTiO3 Hybrid Filler

Effect of silane coupling agent on the morphology, structure, and properties of poly(vinylidene fluoride–trifluoroethylene)/BaTiO3 composites

The Effect of Surface Treatment with Isocyanate and Aromatic Carbodiimide of Thermally Expanded Vermiculite Used as a Functional Filler for Polylactide-Based Composites

Optimization of Water Absorption and Mechanical and Thermal Behavior of Polylactic Acid/Chitosan/Titanium Carbide

Nanocomposites of poly(l-lactide) and surface-grafted TiO2 nanoparticles: Synthesis and characterization

Influence of a Biofiller, Polylactide, on the General Characteristics of Epoxy-Based Materials

Silanization of di-n-octyldichlorosilane as a route to improve the integration of titanium dioxide in polypropylene

Titanium dioxide nanotubes with triazine-methacrylate monomer to improve physicochemical and biological properties of adhesives

Influence of the organic matrix composition on the polymerization behavior and bulk properties of resin composites containing thiourethane-functionalized fillers

Understanding the Effects of Adding Metal Oxides to Polylactic Acid and Polylactic Acid Blends on Mechanical and Rheological Behaviour, Wettability, and Photo-Oxidation Resistance

Thermal and Mechanical Properties of Reprocessed Polylactide/Titanium Dioxide Nanocomposites for Material Extrusion Additive Manufacturing

Synthesis, characterization and thermal behavior of plasticized poly (vinyl chloride) doped with folic acid-modified titanium dioxide

Non-Isothermal Degradation Mechanism of Micro/Nano Titanium Dioxide-Enhanced Polycaprolactone Biocomposite