Abstract:High-performance thermoplastics like polyetheretherketone (PEEK), with their outstanding thermal stability, mechanical properties and chemical stability, have great potential for various structural applications. Combining with additive manufacturing methods extends further PEEK usage, e.g., as a mold insert material in polymer melt processing like injection molding. Mold inserts must possess a certain mechanical stability, a low surface roughness as well as a good thermal conductivity for the temperature control during the molding process. With this in mind, the commercially available high-performance thermoplastic PEEK was doped with small amounts of carbon nanotubes (CNT, 6 wt%) and copper particles (10 wt%) targeting enhanced thermomechanical properties and a higher thermal conductivity. The composites were realized by a commercial combined compounder and filament maker for the usage in a material extrusion (MEX)-based 3D-printer following the fused filament fabrication (FFF) principle. Commercial filaments made from PEEK and carbon fiber reinforced PEEK were used as reference systems. The impact of the filler and the MEX printing conditions like printing temperature, printing speed and infill orientation on the PEEK properties were characterized comprehensively by tensile testing, fracture imaging and surface roughness measurements. In addition, the thermal conductivity was determined by the laser-flash method in combination with differential scanning calorimetry and Archimedes density measurement. The addition of fillers did not alter the measured tensile strength in comparison to pure PEEK significantly. The fracture images showed a good printing quality without the MEX-typical voids between and within the deposited layers. Higher printing temperatures caused a reduction of the surface roughness and, in some cases, an enhanced ductile behavior. The thermal conductivity could be increased by the addition of the CNTs. Following the given results, the most critical process step is the compounding procedure, because for a reliable process–parameter–property relationship, a homogeneous particle distribution in the polymer matrix yielding a reliable filament quality is essential.

Material extrusion 3D printing of polyether ether ketone in vacuum environment: Heat dissipation mechanism and performance

Research on Internal Filling Technology of 3D Printing PEEK

Influence of thermal processing conditions in 3D printing on the crystallinity and mechanical properties of PEEK material

Influence of Thermal Processing Conditions on Mechanical and Material Properties of 3D Printed Thin-Structures Using PEEK Material

Effect of molecular weight on mechanical properties and microstructure of 3D printed poly(ether ether ketone)

On Mechanical, Physical, and Bioactivity Characteristics of Material Extrusion Printed Polyether Ether Ketone

Material Extrusion 3D Printing of PEEK-Based Composites

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Influence of Polyether Ether Ketone (PEEK) Viscosity on Interlayer Shear Strength in Screw Extrusion Additive Manufacturing

In-house processing of 3D printable polyetheretherketone (PEEK) filaments and the effect of fused deposition modeling parameters on 3D-printed PEEK structures

Tensile and Bending Strength Improvements in PEEK Parts Using Fused Deposition Modelling 3D Printing Considering Multi-Factor Coupling

Effect of moisture content in polyether-ether-ketone (PEEK) filament on 3D printed parts

Effect of Temperature History During Additive Manufacturing on Crystalline Morphology of Polyether Ether Ketone

Experimental Investigation on the Mechanical and Dynamic Thermomechanical Properties of Polyether Ether Ketone Based on Fused Deposition Modeling

Design and Modification of a Material Extrusion 3D Printer to Manufacture Functional Gradient PEEK Components

Photosensitive PEEK Ink Enables Digital Light Processing 3D Printed High-performance Small Architected-Plastics

Slowing crystallization to enhance interlayer strength of 3D printed poly (ether ether ketone) parts by molecular design

Improvement in Mechanical Properties of 3D‐Printed PEEK Structure by Nonsolvent Vapor Annealing

Experimental investigation of process parameters in polyether ether ketone 3D printing

Research on the Fused Deposition Modeling of Polyether Ether Ketone

Influence of Layer Thickness and Raster Angle on the Mechanical Properties of 3D-Printed PEEK and a Comparative Mechanical Study between PEEK and ABS