Abstract:The current research about the flow ripple of axial piston pump mainly focuses on the effect of the structure of parts on the flow ripple. Therein, the structure of parts are usually designed and optimized at rated working conditions. However, the pump usually has to work in large-scale and time-variant working conditions. Therefore, the flow ripple characteristics of pump and analysis for its test accuracy with respect to variant steady-state conditions and transient conditions in a wide range of operating parameters are focused in this paper. First, a simulation model has been constructed, which takes the kinematics of oil film within friction pairs into account for higher accuracy. Afterwards, a test bed which adopts Secondary Source Method is built to verify the model. The simulation and tests results show that the angular position of the piston, corresponding to the position where the peak flow ripple is produced, varies with the different pressure. The pulsating amplitude and pulsation rate of flow ripple increase with the rise of pressure and the variation rate of pressure. For the pump working at a constant speed, the flow pulsation rate decreases dramatically with the increasing speed when the speed is less than 27.78% of the maximum speed, subsequently presents a small decrease tendency with the speed further increasing. With the rise of the variation rate of speed, the pulsating amplitude and pulsation rate of flow ripple increase. As the swash plate angle augments, the pulsating amplitude of flow ripple increases, nevertheless the flow pulsation rate decreases. In contrast with the effect of the variation of pressure, the test accuracy of flow ripple is more sensitive to the variation of speed. It makes the test accuracy above 96.20% available for the pulsating amplitude of pressure deviating within a range of ±6% from the mean pressure. However, with a variation of speed deviating within a range of ±2% from the mean speed, the attainable test accuracy of flow ripple is above 93.07%. The model constructed in this research proposes a method to determine the flow ripple characteristics of pump and its attainable test accuracy under the large-scale and time-variant working conditions. Meanwhile, a discussion about the variation of flow ripple and its obtainable test accuracy with the conditions of the pump working in wide operating ranges is given as well.

Investigation of the Main Flow Characteristics Mechanism and Flow Dynamics Within an Axial Flow Pump Based on Different Transient Load Conditions

Analysis of Inter-blade Vortex and Runner Blades Force of Pump Turbine during Load Rejection Period

Experimental and numerical investigations on pressure pulsation in a pump mode operation of a pump as turbine

Analysis of axial force and pressure pulsation of centrifugal pump as turbine impeller based on dynamic mode decomposition

Distribution Features of Flow Patterns and Pressure Pulsations of Pump-Turbine in Five Operating Modes on the Four-Quadrant Plane

Evaluation and Investigation of Hydraulic Performance Characteristics in an Axial Pump Based on CFD and Acoustic Analysis

Flow instability of an axial flow pump-as-turbine using relative streamline coordinates

Performance improvement of an axial-flow pump with inlet guide vanes in the turbine mode

Impact of Typical Steady-State Conditions and Transient Conditions on Flow Ripple and Its Test Accuracy for Axial Piston Pump

Numerical Analysis of Flow Characteristics in Impeller-Guide Vane Hydraulic Coupling Zone of an Axial-Flow Pump as Turbine Device

Numerical Investigation on the Unstable Flow and Its Interaction with the Hump Characteristic in a Pump Turbine at Pump Mode

Numerical and Experimental Investigation of Internal Flow Characteristics and Pressure Fluctuation in Inlet Passage of Axial Flow Pump under Deflection Flow Conditions

Analysis of Flow and Runner Dynamic Response Characteristics under Pump Conditions of Variable-Speed Pump Turbine

Performance analysis and experimental verification of hydraulic driven axial flow pumps

Hydraulic Performance of a Large Slanted Axial‐flow Pump

Analysis of Internal Flow Characteristics of a Startup Pump Turbine at the Lowest Head under No-Load Conditions

Investigation on the unstable flow characteristic and its alleviation methods by modifying the impeller blade tailing edge in a centrifugal pump

Investigation into the Flow Details of Runner Region in A Pump Turbine at Off-Design Conditions

Analysis of the Flow Behavior and Pressure Fluctuation of a Pump Turbine with Splitter Blades in Part-Load Pump Mode

Numerical Simulation and Model Test on Pressure Fluctuation and Structural Characteristics of Lightweight Axial Flow Pump

Hydrodynamic Design and Pulsation Evolution in an Axial-Flow Pump Based On Control Mechanism of Flow-Induced Excitation