Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Deformation behavior and forming process simulation of semi-solid powder rolling based on the combined constitutive model

Establishment of a constitutive model for the solid granules medium and its application in sheet metal forming

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

A Multi-scale Modelling by Coupling Cellular Automata with Finite Element Method and Its Application on Cross-Wedge Rolling

Numerical simulation of continuous hot rolling process for ultra-thick SiCp/2009Al composites plate

A Dislocation Density-based Meshfree Computational Framework for Solid Phase Processing

Model of Metal Microstructure Evolution Considering Shear Effect and Its Simulation Application in Rolling of Heavy Cylinders

Survey on the Application and Design of Material Constitutive Model for Deformable Solid Simulation

Modelling of ultra-thin steel sheet in two-stage tensile deformation considering strain path change and grain size effect and application in multi-stage microforming

Mechanical Analysis of Semi-Solid Metals Shear Deformation During Compression

Modeling morphology evolution and densification during solid-state sintering via kinetic Monte Carlo simulation

Full active counter-roller spinning for thin-walled cylinders: macroscopic deformation mechanism, mesoscopic texture evolution, and forming performance strengthening

Crystal plasticity modelling of multi-stage deformation of ultra-thin sheets considering grain size effect and strain path change

Establishment of macro-micro constitutive model and deformation mechanism of semi-solid Al6061

Research of Constitutive Relation of Metal Powder in High Velocity Compaction

Finite element modeling and analysis for the integration–rolling–extrusion process of spline shaft

Numerical Simulation of 6061 Aluminum Alloys during the Semi-Solid Backward Extrusion

An Integrated Simulation of Multiple-Pass U-10Mo Alloy Hot Rolling and Static Recrystallization

Research Progress on Rolling Forming of Tungsten Alloy

Modeling of material deformation behavior in micro-forming under consideration of individual grain heterogeneity

Constitutive modeling for the simulation of the superplastic forming of TA15 titanium alloy