Abstract:Composite materials in the form of laminates consisting of continuous-fiber-reinforced plies are becoming widely applied in aerospace field. In such laminated structures, delamination is amongst the most usual failure modes, which generally originates from low velocity impacts and interlaminar stress raisers, e.g. free edges, ply drops, access holes, fabrication defects, etc. The delamination will further propagate and lead to considerable degradation of mechanical characteristics, even catastrophic failure of laminates, when the laminates are subjected to additional static loads or cyclic loads. Thus characterization of the fracture toughness and fatigue delamination resistance of composite materials is significant and essential for structural damage tolerant design and reliability assessment, which has attracted extensive investigation during past few decades. However, with regard to the multidirectional laminates, the studies are still limited due to the complication and some different phenomena such as fiber bridging, bifurcation, etc., which are evoked by the multi-directional stacked plies. Thus far there is not yet universal consensus on the effect of stacking sequence on the delamination behavior. To investigate the effect of stacking sequence on the fracture toughness and fatigue delamination propagation behaviors, static and fatigue experiments under pure mode I loading for unidirectional and multidirectional laminates made of T800 carbon/epoxy composites with various ply angle along mid-plane interfaces were carried out. The results indicated the fracture toughness of multidirectional laminates is higher than that of unidirectional one. Besides, the fracture toughness depends on the relative orientation of the adjacent plies along the mid-plane interface and the direction of delamination propagation relative to the fibers. With the increase of relative orientation of the adjacent plies, the effect of the direction of delamination propagation relative to the fibers on the fracture toughness will be smaller. Similar results can also be obtained in fatigue delamination growth. Furthermore, accompanying with SEM images of the fracture surfaces after tests, the complex damage mechanisms, such as fiber bridging and bifurcation, etc. have been deeply investigated.

The Influence of Ply Stacking Sequence on Mechanical Properties of Carbon/Epoxy Composite Laminates

Impact and Flexural Properties Studies on Carbon Fiber Reinforced Epoxy/Polycarbonate Hybrid Laminates with Different Stacking Sequence

Enhancing Impact Energy Absorption, Flexural and Crash Performance Properties of Automotive Composite Laminates by Adjusting the Stacking Sequences Layup

Exploring the influence of stacking sequence on the mechanical properties of flax-ramie bi-quadratic layered hybrid epoxy composites

The Effect of Stacking Sequence on Fatigue Behaviour of Hybrid Pineapple Leaf Fibre/Carbon-Fibre-Reinforced Epoxy Composites

New Method to Study the Effect of Stacking Sequence on Composite Single-Lap Joint Strength

Impact Behavior and Residual Strength of PEEK/CF-Laminated Composites with Various Stacking Sequences

Static and Dynamic Mechanical Properties of Carbon Fiber Reinforced Polymer with Different Stacking Sequences

Influence of stacking sequence on mechanical properties of areca-kenaf fiber- reinforced polymer hybrid composite

Effect Of Stacking Sequence On The Fracture Toughness And Fatigue Delamination Propagation Behavior Of Composite Laminates Under Mode I Loading

Deformation Behavior and Fracture Patterns of Laminated PEEK- and PI-Based Composites with Various Carbon-Fiber Reinforcement

Mechanical performance of carbon-epoxy laminates. Part I: quasi-static and impact bending properties

Effect of Lay-Up Sequence on Fatigue Life of Composite Laminates

Influence of Fibre Stacking Sequence on Impact Resistance and Residual Strength in Flax/Basalt Hybrid Laminates

Development of Improved Flexural and Impact Performance of Kevlar/Carbon/Glass Fibers Reinforced Polymer Hybrid Composites

Mechanical properties and failure mechanisms of composite laminates with classical fabric stacking patterns

Evaluating the mechanical behavior of carbon composites with varied ply-thicknesses using acoustic emission measurements

Stacking Sequence Effect on the Fracture Behavior of Narrow L-Shaped Cross-Ply Laminates: Experimental Study

Modeling and Characterization of Fatigue Strength of Laminated Composites with Knitted Fabric Reinforcement

Experimental Study on the Influence of Optimised Automated Fibre Placement Processing Parameters on the Impact Response and Residual Flexural Strength of AS4/APC-2 Laminates

Influence of inlay yarn type and stacking sequence on mechanical performance of knitted uni-directional thermoplastic composite prepregs