Abstract:The stacking sequences of fiber-reinforced composites for optimization of turbine blades with the best performance have become a focus of attention. However, the optimization and design principles of its flexural performance are not yet mature. Referring to the problems in previous work, a 3D finite element flexural model of carbon fiber reinforced composites was established based on the Abaqus/Explicit VUMAT subroutine through the Tsai-Wu failure criterion. The influencing laws and optimization mechanisms of different stacking patterns (e.g., different orientations, number of orientation plies, combination of multiple orientation plies, and symmetry/asymmetry structures) on the flexural properties of the composites were systematically investigated, and corresponding design references for the optimization of stacking patterns were given. The results show that the smaller the value of ∣θ−45°∣ (θ represents the angle of the orientation ply), the more obvious the stress reduction of the orientation ply, and the orientation ply located in the outer layer is more conducive to the improvement of flexural performance. As the number of orientation plies increases, the flexural strength and displacement increase, but the stability decreases, in which the laminate with 50 % 0° orientation plies has the best overall performance. In addition, the stability ranking of the laminate stacking sequences for the same 0° orientation ply proportion is: multi-orientation asymmetric > multi-orientation symmetric > single-orientation symmetric. In particular, the [75/02/60/30/02/15] laminate has the best overall performance with the flexural strength of 974 MPa and the Y-axis offset of 0.057 mm, and its stability is 66 % higher than that of the [15/02/75]S laminate. Under the same tensile/compressive stresses, the actual stress of the warp/weft in the orientation ply is less than the maximum ideal stress and the stress of Y-axis direction SY ≠ 0, which delays the fracture of the orientation ply and causes displacement offset, and the increase of the number of orientation plies will aggravate this effect. The obtained highlighted results can provide valuable references for the design and optimization of stacking patterns of plain fabric-reinforced laminates with high flexural properties.

Stacking Sequence Effect on the Fracture Behavior of Narrow L-Shaped Cross-Ply Laminates: Experimental Study

Effect Of Stacking Sequence On The Fracture Toughness And Fatigue Delamination Propagation Behavior Of Composite Laminates Under Mode I Loading

New Method to Study the Effect of Stacking Sequence on Composite Single-Lap Joint Strength

Effect of Lay-Up Sequence on Fatigue Life of Composite Laminates

Mechanical properties and failure mechanisms of composite laminates with classical fabric stacking patterns

INTERLAMINAR STRESS ANALYSIS OF COMPOSITE LAMINATES SUBJECTED TO IN-PLANE LOADING

Mechanical behavior in bending deformation of thermoplastic composite laminates with different stacking sequences

Delamination in Carbon Fiber Epoxy DCB Laminates with Different Stacking Sequences: R-curve Behavior and Bridging Traction-Separation Relation

Experimental and Numerical Investigations of Compression Stability of Stiffened Composite Panel with Ply Interleaving

The Influence of Ply Stacking Sequence on Mechanical Properties of Carbon/Epoxy Composite Laminates

Tensile Behaviour of Multilayer Knitted Fabric Composites with Different Stacking Configuration

Experimental Investigation of Stacking Interface on Mode II Interlaminar Behaviour of Self-Healable Vitrimeric CFRP

Regulating Crack Propagation in Laminated Metal Matrix Composites Through Architectural Control

Experimental and Numerical Investigation of Open Hole Carbon Fiber Composite Laminates under Compression with Three Different Stacking Sequences

Progressive Failure Analysis of Composite Laminates Subjected to Transverse Loading with Augmented Finite Element Method

Delamination Propagation Manipulation of Composite Laminates under Low-Velocity Impact and Residual Compressive Strength Evaluation

Numerical and Analytical Investigation Into the Effects Of Stacking Sequences on the Distortion of Asymmetric Composite Laminates in the Curing Cycle

Load-Bearing Behaviour and Damage Mechanism of Filled-Hole Composite Laminates Subjected to Compressive Loading

The damage of low-velocity impacted cfrp laminates with different stacking sequences based on micro-mechanics of failure

Effects of stacking sequence and rotation angle of patch on low velocity impact performance of scarf repaired laminates

Numerical Investigation on the Design and Optimization of Stacking Pattern for High Flexural Performance Carbon Fiber Reinforced Resin Matrix Composites