Abstract:The stacking sequences of fiber-reinforced composites for optimization of turbine blades with the best performance have become a focus of attention. However, the optimization and design principles of its flexural performance are not yet mature. Referring to the problems in previous work, a 3D finite element flexural model of carbon fiber reinforced composites was established based on the Abaqus/Explicit VUMAT subroutine through the Tsai-Wu failure criterion. The influencing laws and optimization mechanisms of different stacking patterns (e.g., different orientations, number of orientation plies, combination of multiple orientation plies, and symmetry/asymmetry structures) on the flexural properties of the composites were systematically investigated, and corresponding design references for the optimization of stacking patterns were given. The results show that the smaller the value of ∣θ−45°∣ (θ represents the angle of the orientation ply), the more obvious the stress reduction of the orientation ply, and the orientation ply located in the outer layer is more conducive to the improvement of flexural performance. As the number of orientation plies increases, the flexural strength and displacement increase, but the stability decreases, in which the laminate with 50 % 0° orientation plies has the best overall performance. In addition, the stability ranking of the laminate stacking sequences for the same 0° orientation ply proportion is: multi-orientation asymmetric > multi-orientation symmetric > single-orientation symmetric. In particular, the [75/02/60/30/02/15] laminate has the best overall performance with the flexural strength of 974 MPa and the Y-axis offset of 0.057 mm, and its stability is 66 % higher than that of the [15/02/75]S laminate. Under the same tensile/compressive stresses, the actual stress of the warp/weft in the orientation ply is less than the maximum ideal stress and the stress of Y-axis direction SY ≠ 0, which delays the fracture of the orientation ply and causes displacement offset, and the increase of the number of orientation plies will aggravate this effect. The obtained highlighted results can provide valuable references for the design and optimization of stacking patterns of plain fabric-reinforced laminates with high flexural properties.

Tensile Behaviour of Multilayer Knitted Fabric Composites with Different Stacking Configuration

Mechanical properties and failure mechanisms of composite laminates with classical fabric stacking patterns

Understanding the Impact of Fibre Wrinkle Architectures on Composite Laminates Through Tailored Gaps and Overlaps

Tensile properties of multilayered biaxial weft knitted fabric reinforced composite material

Numerical Investigation on the Design and Optimization of Stacking Pattern for High Flexural Performance Carbon Fiber Reinforced Resin Matrix Composites

Influence of inlay yarn type and stacking sequence on mechanical performance of knitted uni-directional thermoplastic composite prepregs

Deformation and Fracture Mechanisms of Automated Fiber Placement Pre-Preg Laminates under Out-of-plane Tensile Loading

The Influence of Ply Stacking Sequence on Mechanical Properties of Carbon/Epoxy Composite Laminates

Effects of fabric architectures on mechanical and damage behaviors in carbon/epoxy woven composites under multiaxial stress states

Mechanical Deformation Mechanisms in Knitted Fabric Composites

The influence of the inter-ply hybridisation on the mechanical performance of composite laminates: Experimental and numerical analysis

Multi‐layer structure design, fabrication and numerical simulations of 3D woven spacer fabric composites with improved mechanical properties

Elastic and Fracture Behavior of Three-Dimensional Ply-to-Ply Angle Interlock Woven Composites: Through-Thickness, Size Effect, and Multiaxial Tests

Effect of stacking configuration on dynamic tensile properties of braided carbon fibre composites under medium-low strain rates

Experimental investigation on the effects of fabric architectures on mechanical and damage behaviors of carbon/epoxy woven composites

Manufacturing and Flexural Testing of Woven Lattice Sandwich-Ply Laminate Composites

Selection and analysis of optimum stacking sequence and geometry dimensions on bismaleimides composite joints under tensile loading

Investigation of the translaminar fracture behavior of the fiber-reinforced composites stitched perpendicular to their plane

Comparative studies on the effect of fabric structure on mechanical properties of carbon fiber/epoxy composites

Experimental Investigation on Tensile Properties of Carbon Fabric-Glass Fabric-Kevlar Fabric-Epoxy Hybrid Composite Laminates

Mechanical Testing of 3D Fabric Composites and Their Matrix Material SC-15