Abstract:Goods made of beryllium bronzes got widespread use in the industry due to the complex of properties: high heat conductivity, strength, hardness, wear resistance, and corrosion resistance. They are not magnesium-based and do not spark on impact; therefore, they are essential for the production of non-sparking tools. The alloys of this system are used in the electrical engineering industry; consequently, it is necessary to pay attention to the improvement of the material’s electrical conductivity. The paper studies the microstructure, microhardness, and electrical conductivity of the Cu–2 wt.% Be alloy exposed to high-pressure torsion (HPT). The authors investigated the microstructure and fine structure of the alloy in various states. The study showed that HPT leads to the formation of an ultrafine-grained nanostructured (UFG NS) state with an average size of grains/subgrains of 22±1 mmn. Additional ageing of samples after HPD led to a slight increase in the grains/subgrains size up to 31±1 mmn. In both states, the authors observed nanosized deformation twins. The authors studied the dependences of microhardness and electrical conductivity of the alloy after HPD on the time of further ageing. The study identified that the microhardness increases from 122±3 HV in the initial state up to 525±8 HV after HPD and ageing. The investigation shows that the electrical conductivity substantially better recovers after ageing of the UFG NS state compared to the initial state. The electrical conductivity of the UFG NS state increased from 14.5±0.1 % IACS up to 27.5±0.6 % IACS in conditions similar to the initial state ageing. Therefore, resulting from such processing, the Cu–2 wt.% Be alloy is characterized by its advanced strength properties and electrical conductivity.

Strength and electrical conductivity of UFG Cu-Fe alloys subjected to HPT

Development of Powder Metallurgy High Speed Steel

Microstructural Modification and Mechanical Improvement of Ultrafine-Grained Ti Alloy Through Electron Wind Force: an Innovative Approach

Microstructure and Mechanical Properties of Al-4Mg-0.3Cu Alloy after HPT and Postdeformation Annealing

Microstructure Evolution during High-Pressure Torsion in a 7xxx AlZnMgZr Alloy

Thermal stability and corrosion resistance of ultrafine-grained high-entropy Fe30Ni30Mn30Cr10 alloy

The Evolutions of Microstructure, Texture and Hardness of A1050 Deformed by HPT at the Transition Area

Microstructure Evolution and Mechanical Properties of AlCoCrFeNi2.1 Eutectic High-Entropy Alloys Processed by High-Pressure Torsion

The influence of aging on microhardness and electrical conductivity of Cu–2 wt. % Be alloy

EFFECT OF HIGH PRESSURE TORSION ON STRUCTURE AND MECHANICAL PROPERTIES OF Al–Ca–Cu ALLOY

Ultra-High Strength in FCC+BCC High-Entropy Alloy via Different Gradual Morphology

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Achieving highly strengthened Al-Cu-Mg alloy by grain refinement and grain boundary segregation

Magnetic Characterization of HPT-deformed Fe-Si Soft Magnetic Alloys Before and After Heat Treatment and Internal Stress Calculations

Effect of V content on the microstructure and mechanical properties of HPT nanostructured CoCrFeMnNiVx high entropy alloys

The nanoscale mechanisms of strengthening and ductility enhancement in an Al–Mg–Si–Mn alloy on processing by high-pressure torsion

Effect of High-Pressure Torsion Temperatures on the Precipitation and Properties of Cu-Cr Alloy

Microstructural evolution and properties of a Cu-Fe-Mn-P alloys with high strength and high conductivity

Strength enhancement of an aluminum alloy through high pressure torsion

Microstructures and properties of graphene nanoplatelets reinforced Cu/Ti3SiC2/C nanocomposites with efficient dispersion and strengthening achieved by high-pressure torsion