Abstract:Biomedical sciences facilitated fast detection methods for many diseases recently. The development of this field has led to the dynamic development of Lab-On-a-Chip devices which are portable, require small sample size and have low cost. Fluid manipulation in such bioanalytical systems is a key issue. One of the key features of these devices is the sample preparation which includes the dilution and complete mixing of the analyte with reagents of adequate buffer solution. The mixing possibilities are limited on microscale, since turbulent flow cannot occur due to the dominant viscosity. Chaotic advection can be considered as an ideal mixing method in microfluidic channels as the flows are laminar. The herring-bone like ridges on the channel of the herring-bone type micromixers (Figure 1) act as anisotropic fluid resistance generating secondary transversal flow. The Laminar Flow interface of COMSOL Multiphysics® software was used to solve the velocity field of the micromixer to characterize fluid flow properties. For modelling the mixing phenomena two approaches were used. Mixing by diffusion along the channel was modeled with Transport of Diluted Species interface. To avoid numerical diffusion and high computational cost we used the Particle Tracing module to observe mixing at the level of particles. To optimize the mixing efficiency we conducted a parametric sweep on the thickness of the ridges. Secondary flow and the rotation caused by the herring-bone structure were well observable in the velocity field (Figure 2). The concentration distribution calculated by COMSOL Multiphysics® showed that a high concentration fluid layer was rotated into a low concentration region resulting more surface area for mixing by diffusion. Poincaré map of particle trajectories (Figure 3) showed the layered structure of particle distribution which was similar to the baker's transformation. Modeled herring-bone structures were fabricated in polydimethylsiloxane (PDMS) using multilayer technology. The SU-8 epoxy-based photoresist was applied as molding replica. An improved 3D multilayer formation from SU-8 was developed so that microfluidic systems with high aspect ratio sidewalls and advanced functional parts could be fabricated well. Dye was used for the measurement of mixing by diffusion and yeast cells were used for the particle approach. Pictures were recorded in inverted microscope with bright field imaging. The scattered light from the yeast cells provided good signal (Figure 4). The measurements confirmed the rotation caused by the ridges and also the layered flow characteristics. COMSOL Multiphysics® was used in this study to simulate mixing by diffusion and by secondary flow. Particle tracing model was applied to simulate the mixing of cells in the microchannel. Results agreed well with the measurement, an optimal herring-bone structure was proposed for integration into a bioanalytical system.

CFD-based approach to design the heart-shaped micromixer with obstacles

A Novel Passive Micromixer with Modified Asymmetric Lateral Wall Structures

Optimization of a novel micromixer with fan-shaped obstacles

Design, Implementation, and Optimization of a Novel Chaotic Micromixer

Optimization of the Herringbone Type Micromixer Using Numerical Modelling and Validation By Measurements

Design and Experimental Study of Staggered Oriented Ridges Micromixers

Influence of Structural Parameters on the Performance of an Asymmetric Rhombus Micromixer with Baffles

An Enhanced Electroosmotic Micromixer with an Efficient Asymmetric Lateral Structure.

Numerical Simulation on Fluid Mixing by Effects of Geometry in Staggered Oriented Ridges Micromixers

A Modified T-Mixer Simulation, Fabrication, and Characterization For 1D Diffusion Controlled Studies

An Effective Passive Micromixer Employing Herringbone Structure Category: 4 Biomedical and Chemical Micro Sensors and Systems

Experimental fluid dynamics characterization of a novel micropump-mixer

Design and development of an efficient fluid mixing for 3D printed lab-on-a-chip

An Investigation of Flow Patterns and Mixing Characteristics in a Cross-Shaped Micromixer within the Laminar Regime

An embedded obstacle type micromixer-concentration gradient generator based on capillary driven

Numerical and Experimental Investigation on a Planar Passive Micromixer Embedded with Omega-Shaped Obstacles for Rapid Fluid Mixing

Design and Analysis of the Cross-Linked Dual Helical Micromixer for Rapid Mixing at Low Reynolds Numbers

A Three-Dimensional Micromixer Using Oblique Embedded Ridges

Numerical Investigation of Flow Patterns and Mixing Characteristics in a 3D Micromixer with Helical Elements over Wide Reynolds Numbers

Numerical study of a novel electroosmotic active micromixer with twin diamond-shaped chambers and sawteeth

Optimization Analysis of the Staggered Herringbone Micromixer Based on the Slip-Driven Method