Abstract:During the past years, the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has increased from 3.8% to 25.7%, making them the best candidate for the next-generation photovoltaic devices. Two dominant PSC architectures have evolved, a regular n-i-p structure with mesoscopic or planar heterojunction and an inverted p-i-n planar structure. Compared to the regular n-i-p PSCs, the inverted p-i-n PSCs possess the advantages of lower synthesis temperature, no hysteretic effect and good compatibility with the tandem solar cells. For p-i-n PSCs, the hole transport layer (HTL) determines the hole transport efficiency and crystallinity of perovskite, so it plays a crucial role in the stacked devices. The conventional organic HTL of PEDOT:PSS-based PSCs can achieve satisfying PCEs, but may be able to impede the commercialization of perovskite photovoltaic devices because of their high price and acidity-induced poor stability. By comparison, the inorganic P-type NiOx with wide band gap exhibits low cost, superior chemical stability and high hole mobility without corrosion to perovskite layer. Unlike the most reported spin-coated NiOx nanoparticle films, we used sputtered NiOx as HTL for application in FA-based PSCs and achieved a PCE of 20.05%. After systematically optimizing the sputtering parameters, including power, time and argon flow rate, we obtained better crystal quality, better transparency, proper energy level, and higher hole mobility of NiOx film. Reducing the interstitial vacancies and defects in NiOx films attributes to decreased nonradiative recombination losses, which mainly cause the hole accumulation near the perovskite/NiOx interface. Finally, a champion device with open-circuit voltage (Voc) of 1.09 V, current density (Jsc) of 23.4 mA/cm 2 , fill factor (FF) of 78% and PCE of 20.05% are obtained. This work has important significance for preparation of large-area perovskite solar cell modules.

Oxide/Halide/Oxide Architecture for High Performance Semi‐Transparent Perovskite Solar Cells

Printed high-mobility p-type buffer layers on perovskite photovoltaics for efficient semi-transparent devices

Interface Reactive Sputtering of Transparent Electrode for High‐Performance Monolithic and Stacked Perovskite Tandem Solar Cells

Self‐Encapsulating Thermostable and Air‐Resilient Semitransparent Perovskite Solar Cells

Hierarchical Dual‐Scaffolds Enhance Charge Separation and Collection for High Efficiency Semitransparent Perovskite Solar Cells

Semitransparent Perovskite Solar Cells with Dielectric/Metal/Dielectric Top Electrodes

Electron-beam-evaporated NiOX for efficient and stable semi-transparent perovskite solar cells and modules

Working from Both Sides: Composite Metallic Semitransparent Top Electrode for High Performance Perovskite Solar Cells

Fullerene‐Free p–i–n Perovskite Solar Cells: Direct Deposition of Tin Oxide on Perovskite Layer Using Ligand Bridges

Ultrathin chromium oxide buffer layer by reactive thermal deposition for high-performance semitransparent perovskite solar cells

High‐Performance Semitransparent and Bifacial Perovskite Solar Cells with MoO x /Ag/WO x as the Rear Transparent Electrode

Sputtered Niox Films As Hole Transport Layers for FA-Based Perovskite Solar Cell Application

Cerium-doped Indium Oxide Transparent Electrode for Semi-Transparent Perovskite and Perovskite/silicon Tandem Solar Cells

Dual Interfacial Modifications Enable High Performance Semitransparent Perovskite Solar Cells with Large Open Circuit Voltage and Fill Factor

Ultra-thin high efficiency semitransparent perovskite solar cells

Pyrophosphate interlayer improves performance of semi-transparent perovskite solar cells

Near-neutral-colored Semitransparent Perovskite Films Using a Combination of Colloidal Self-Assembly and Plasma Etching

A Scalable Integrated Dopant‐Free Heterostructure to Stabilize Perovskite Solar Cell Modules

Thermally-stable and highly-efficient bi-layered NiOx-based inverted planar perovskite solar cells by employing a p-type organic semiconductor

A Semitransparent Inorganic Perovskite Film for Overcoming Ultraviolet Light Instability of Organic Solar Cells and Achieving 14.03% Efficiency

Highly Stable and Enhanced Performance of p–i–n Perovskite Solar Cells via Cuprous Oxide Hole-Transport Layers