Abstract:Expertise of packaging for optoelectronic components requires the solution of optical, mechanical, and electrical problems in the same way. The purpose of this paper is to present three-dimensional simulations using finite-element method (FEM) of thermomechanical stresses and strains in 1550-nm laser modules induced by Nd:YAG crystal laser welds and thermal cycles on main subassembly laser submount. Nonlinear FEM computations, taking into account of experimental sigma(epsiv) measured curves, show that the laser welding process can induce high level of strains in columns of the laser platform, bearing the laser diode, responsible of an optical axis shift and a gradual drop of the optical power in relation with relaxation of accumulated stresses in the subassembly (W. M. Sherry et al., ldquoHigh performance optoelectronic packaging for 2.5 and 10 Gb/s laser modules,rdquo in Proc. Electron. Compon. Technol. Conf., 1996, pp. 620-627). Typical stresses are close to 160 MPa with drift about 5 MPa with the dispersion of energy level of the laser Nd: YAG beam. The introduction of both material and process dispersion in order to evaluate their impact on product lifetime distribution has been taking into account. In the case of thermal cycles, stresses can occur on elements sensitive to coefficient of thermal expansion mismatches such as solder joints between the laser platform and thermoelectric cooler and as fiber glued into the pigtail leading to crack propagation with sudden drop of optical power. A previous paper demonstrated that laser submount is the most sensitive part of optical system (Deshayes, et al., ldquoThree-dimensional FEM simulations of thermal mechanical stresses in 1.55 mum laser modules,rdquo Microelectron. Rel., vol. 43, no. 7, pp. 1125 -1136, Jul. 2003). Experimental analyses were also conducted to correlate simulation results and monitor the output optical power of laser modules after 500 thermal cycles ( -40degC/ + 85degC VRT).

Finite Element Thermal Analysis of Optical Elements in a Laser Incoherent Space Beam Combiner

10 kW rectangular laser beam generation with incoherent space combiner

Theoretical Analysis of Thermal-Lensing Effect in a High Power Exciplex Pumped Cs Vapor Laser.

Space-Incoherent Beam Combining of Rectangular Spot Using 18 Fiber-Transmitted Semiconductor-Laser Beams

Thermal Analysis of the Laser-Induced Thermal Deformation of a Diffractive Optical Element in a Single-Aperture Coherent Beam Combining System

Analysis of far-field characteristics of spatial coherent beam combining fiber lasers

Thermal integration analysis of optical machines for space-based laser communications

Investigation on the thermal blooming effect in a high power spectral beam combining fiber laser system

High-robustness good-beam-quality 3×1 signal combiner device for 10-kW all-fiber laser combining applications

Incoherent combination of fiber lasers using a collimating and focusing optical system in fiber-based laser fusion

Numerical Simulation of Waveguide Opto-Combiner Fabricated by Femtosecond Laser

High Power Semiconductor Laser Beam Combining Technology and Its Applications

Analytical Study on the Steady-State Thermal Blooming of Incoherent Combining Beam

High power mid-infrared side-pump combiner with good thermal stability based on the point-by-point fusion splicing technique

High power signal combiner for fiber lasers

Spatial Beam Shaping of a Focused Laser with Quasi-Near-field Characteristics Based on a Concatenated Fuzzy Matching Algorithm

High-Power Coherent Beam Combining of Two Photonic Crystal Fiber Lasers

Coherent Beam Combination of Ultrafast Fiber Lasers

All-fiber cascaded combiners for high-power adjustable-ring mode laser beam with a flattop central beam

Laser Coherent Combination with Circular Array of Airy Beams

Simulations of Thermomechanical Stresses and Optical Misalignment in 1550-nm Transmitter Optoelectronic Modules Using FEM and Process Dispersions