Abstract:In this study, the effect of the cell density of monolithic catalysts was investigated and further mathematically modeled on cordierite supports used in CO 2 methanation. Commercial cordierite monoliths with 200, 400, and 500 cpsi cell densities were coated by immersion into an ethanolic suspension of Ni/CeO 2 active phase. SEM–EDS analysis confirmed that, owing to the low porosity of cordierite (surface area < 1 m 2 g −1 ), the Ni/CeO 2 diffusion into the walls was limited, especially in the case of low and intermediate cell density monoliths; thus, active phase was predominantly loaded onto the channels' external surface. Nevertheless, despite the larger exposed surface area in the monolith with high cell density, which would allow for better distribution and accessibility of Ni/CeO 2 , its higher macro-pore volume resulted in some introduction of the active phase into the walls. As a result, the catalytic evaluation showed that it was more influenced by increments in volumetric flow rates. The low cell density monolith displayed diffusional control at flow rates below 500 mL min −1 . In contrast, intermediate and high cell density monoliths presented this behavior up to 300 mL min −1 . These findings suggest that the interaction reactants-catalyst is considerably more affected by a forced non-uniform flow when increasing the injection rate. This condition reduced the transport of reactants and products within the catalyst channels and, in turn, increased the minimum temperature required for the reaction. Moreover, a slight diminution of selectivity to CH 4 was observed and ascribed to the possible formation of hot spots that activate the reverse water–gas shift reaction. Finally, a mathematical model based on fundamental momentum and mass transfer equations coupled with the kinetics of CO 2 methanation was successfully derived and solved to analyze the fluid dynamics of the monolithic support. The results showed a radial profile with maximum fluid velocity located at the center of the channel. A reactive zone close to the inlet was obtained, and maximum methane production (4.5 mol m −3 ) throughout the monolith was attained at 350 °C. Then, linear streamlines of the chemical species were developed along the channel.

Simulation Study of Ceramic Fibrous Structured Catalysts for CO2 Methanation—Enhancement of the Performance and Comparison to Pellet Catalysts

Effects of Catalyst Activity, Particle Size and Shape, and Process Conditions on Catalyst Effectiveness and Methane Selectivity for Fischer–Tropsch Reaction: A Modeling Study

Optimization of Catalyst Pellet Structures and Operation Conditions for CO Methanation

CFD simulation of methanation reaction over 3D-printed monolithic catalysts: A comparative study

Particle-scale simulation on the effect of catalyst shape on the strongly exothermic Fischer–Tropsch synthesis process

Monolithic Fiber/foam-Structured Catalysts: Beyond Honeycombs and Micro-Channels

Structural optimization of 3D printed SiC scaffold with gradient pore size distribution as catalyst support for methanol steam reforming

Enhanced Performance of Catalyst Pellets for Methane Dry Reforming by Engineering Pore Network Structure

Fibrous Material Structure Developments for Sustainable Heterogeneous Catalysis – An Overview

Simulative Optimization of Catalyst Configuration for Biogas Dry Reforming

Core‐Shell Catalyst Pellets for CO2 Methanation in a Pilot‐Scale Fixed‐Bed Reactor

Modeling and experimental analysis of CO2 methanation reaction using Ni/CeO2 monolithic catalyst

Optimizing Catalyst Supports at Single Catalyst Pellet and Packed Bed Reactor Levels: A Comparison Study

Modeling phase formation on catalyst surfaces: Coke formation and suppression in hydrocarbon environments

Catalytic Non-Thermal MilliPulse Plasma for Methanation of CO2 without Carbon Deposition and Catalyst Deactivation

Cross-flow inducing structured catalyst for reduced concentration polarization in packed bed membrane reactors

3D printed Ni/Al2O3 based catalysts for CO2 methanation - a comparative and operando XRD-CT study

High-capacity CO/CO2 methanation reactor design strategy based on 1D PFR modelling and experimental investigation

Sintering enhances turn-over frequency of nanoparticles: A case study of FexCy catalyst using reactive MD simulations

Real-time Dynamics and Structures of Supported Subnanometer Catalysts Via Multiscale Simulations

Pd/P–CeO2–Al2O3 coatings supported on foam ceramic with controlled morphology for high-performance CO2 methanation