Abstract:In order to implement numerical simulation of the thermal-mechanical behaviors in the nuclear fuel rods, a three-dimensional finite element model is established. The thermal-mechanical behaviors at the initial stage of burnup in both the pellet and the cladding are obtained. Comparison of the obtained numerical results with those from experiments validates the developed finite element model. The effects of the constraint conditions, several operation and structural parameters on the thermal-mechanical performances of the fuel rod are investigated. The research results indicate that: (1) with increasing the heat generation rates from 0.15 to 0.6 W/mm(3), the maximum temperature within the pellet increases by 99.3% and the maximum radial displacement at the outer surface of the pellet increases by 94.3%. And the maximum Mises stresses in the cladding all increase; while the maximum values of the first principal stresses within the pellet decrease as a whole; (2) with increasing the heat transfer coefficients between the cladding and the coolant, the internal temperatures reduce and the temperature gradient remains similar; when the heat transfer coefficient is lower than a critical value, the temperature change is sensitive to the heat transfer coefficient. The maximum temperature increases only 7.13% when h changes from 0.5 W/mm(2) K to 0.01 W/mm(2) K, while increases up to 54.7% when h decreases from 0.01 W/mm(2) K to 0.005 W/mm(2) K; (3) the initial gap sizes between the pellet and the cladding significantly affect the thermal-mechanical behaviors in the fuel rod; when the gap size varies from 0.03 mm to 0.1 mm, the highest temperature in the pellet increases by 19.7%, and the maximum first principal stress at the outer pellet surface decreases by 17.4%; it is critical to optimize the gap size in order to reduce the pellet-cladding mechanical interaction and avoid their contact at early stage. This study lays a foundation for the further research on the irradiation-induced mechanical behaviors in the fuel rods. (C) 2011 Elsevier Ltd. All rights reserved.

Thermal analysis of baffle jetting in fuel rod assembly

Numerical Analysis of Effects of Vane Deflection Angle on Flow-Thermal Characteristics in a Fuel Rod Assembly

Large Eddy Simulation on the Lead-Bismuth Eutectic Jet at Reactor Core Outlet

Numerical Study on the Boiling Heat Transfer and Critical Heat Flux in a Simplified Fuel Assembly with 2×2 Helical Cruciform Rods

Analysis of hypothetical channel flow blockage of a tubular fuel assembly in a 10 MWth nuclear research reactor

Investigation of Thermal Striping in Prototype Fast Breeder Reactor Using Ten-Jet Water Model

A Particle Finite Element Method Based Partitioned Paradigm for the Axial-Flow-induced Vibration Analysis of NHR200-II Fuel Rod

Numerical Investigation of Flow and Heat Transfer Characteristics of Subcooled Boiling in a Single Rod Channel With/without Spacer Grid

CFD evaluation of turbulence models for flow simulation of the fuel rod bundle with a spacer assembly

CFD analysis of thermal-hydraluic behaviors in a LBE cooled 19-pin wire wrapped bundle under porous lumped blockage conditions

Numerical Study of the Effect of Helical Fuel Rod Geometry on Single-Phase Flow and Heat Transfer Characteristics

Les Of Normally Impinging Round Air-Jet With Heat Transfer At Moderate Reynolds Numbers

Numerically simulating the thermal–hydraulic characteristics within the fuel rod bundle using CFD methodology

Enhancing Thermal–Hydraulic Performance in Nuclear Reactor Subchannels with Al2O3 Nanofluids: A CFD Analysis

Numerical and Experimental Analysis of LBE Flow and Heat Transfer Characteristics in Hexagonal Rod Bundles

Cfd Investigating the Effects of Different Mixing Vane Designs on the Localized Thermal-Hydraulic Characteristics in the Rod Bundles with Grid Spacer

Dynamic Mode Decomposition of Impinging Jet in a T-Junction

Study on the Prediction of DNB-Type Critical Heat Flux in Rod Bundle Under Motion Conditions

Effect of superhydrophobic surfaces on rod bundle flow dynamics

Three-dimensional FE analysis of the thermal-mechanical behaviors in the nuclear fuel rods

COMPUTATIONAL THERMAL ANALYSIS OF TURBULENT FORCED-CONVECTION FLOW IN AN AIR CHANNEL WITH A FLAT RECTANGULAR FIN AND DOWNSTREAM V-SHAPED BAFFLE