Abstract:The aim of this study is to enhance the plasticity and strength of M2 high-speed steel through electron beam melting (EBM) technology. Therefore, by controlling different melting times to change the energy input, a gradient distribution of grain size and uniform distribution of carbides can be achieved. During the deformation process, the gradient structure causes geometrically necessary dislocations (GND) to accumulate near the boundary of regions in the soft zone, resulting in compressive stress in the soft zone and tensile stress in the hard zone, ultimately achieving heterogeneity-induced (HDI) work hardening. This study is to EBM technology for the design and fabrication of three types of M2 high-speed steel samples, denoted as SS-1, SS-2, and SS-3, utilizing three distinct scanning strategies: single melting, double melting, and a combination thereof. The microstructure and phase evolution of these samples were comprehensively characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron backscatter diffraction (EBSD) techniques. The findings demonstrate that when sample SS-3 was subjected to the combined scanning strategy involving both single melting and double melting approaches, its crystal structure exhibited a gradient distribution along with the presence of back stress during tensile testing. Sample SS-3 achieved an average tensile strength of 1479 MPa with an average elongation rate of 1.8%. This represents an enhancement in average tensile strength by approximately 8.6% compared to sample SS-1 (∼1362 MPa) and a significant increase in average elongation rate by around 20% compared to SS-1 (∼1.44%). The gradient grain structure materials show the microstructure transformation from fine grain to coarse-grain in the same material, thus reducing the stress concentration caused by the change of mechanical properties in each region. The SS-3 sample can maintain significant ductility while improving tensile strength. Consequently, this represents a pivotal direction for the advancement of high-performance structural materials. The conducted experimental studies have demonstrated that geometrically necessary dislocations (GNDs) and their associated strain hardening play a crucial role in enhancing the strength of grain structure materials. Additionally, these are essential to achieve an exceptional synergy between strength and toughness in these materials.

Improvement of Mechanical Properties of 20CrMnTi Steel through Microstructure Modification

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Influences of Partial Substitution of C by N on the Microstructure and Mechanical Properties of 9cr18mo Martensitic Stainless Steel

Improving Mechanical Properties of a Forged High-Manganese Alloy by Regulating Carbon Content and Carbide Precipitation

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Microstructure manipulation mechanism and mechanical properties improvement of H13 steel via trace nano-(TiC + TiB2) particles

Microstructure and mechanical properties of a novel medium Mn steel with Cr and Mo microalloying

Effect of Cr–Mo addition on the microstructure and mechanical properties of medium‐carbon steel

The Properties of 1500 Mpa Grade Alloy Steel with Carbide Free Bainite/Martensite Mixed Microstructures

Tailoring microstructure and mechanical performance of a β-solidifying TiAl alloy via martensitic transformation

Microstructure and Properties of a Low Carbon Ti-V Microalloyed Steel

Drastic enhancement in hot-workability and microstructural refinement of TiAl alloys via martensitic transformation: A comparative study

Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Improvement of mechanical property of M2 high-speed steel with hetero-microstructure tailored via electron beam melting

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering

The Influence of Cr Addition on the Microstructure and Mechanical Properties of Fe-25Mn-10Al-1.2C Lightweight Steel

Effect of intercritical annealing temperature on microstructure and mechanical properties of V-Ti-Mo microalloyed medium Mn steel

Effect of Heat Treatment on Microstructure and Properties of Improved 40crni2si2mov Steel

Optimizing Heat Treatment to Improve the Microstructures and Mechanical Properties of 5crnimov Steel

Effects of titanium addition on austenite grain size and mechanical properties of high manganese steel

Relationship of microstructure on the mechanical and splitting fracture properties of a high carbon forging steel for connecting rod