Abstract:Metal matrix composite (MMC) has been well known for its superior material properties com- pared with traditional composite. A new method is introduced to improve the properties of MMC in the sense that the ends of the reinforcement phase of the composite are allowed to extend out of the mold and cooled by a heat sink in order to promote the rate of heat transfer through the fibers and promote the for- mation of primary alpha phase around the reinforcement. This paper presents the experimental results ob- tained from the foundry in the University of Wisconsin - Milwaukee and some numerical simulation re- sults of the solidification process in the cast mold. Heat transfer analysis of solidification of metal matrix composites has been carried out to understand the forma- tion of solidification microstructure. It is of prime interest in casting industry because composites are widely used in many applications such as in the manufacturing of engine components of a vehicle and brake rotors of selected ve- hicles. It is highly desirable to produce composite cast- ings with superior material properties, which can be ob- tained through improved solidified microstructure that directly influence several properties. The traditional way of producing a composite compo- nent is to fill the casting mold with liquid melt containing the reinforcement and let the setup to cool below its melt- ing temperature as a result of heat transfer primarily through the mold and cooled by convection. The micro- structures of composites containing fibers or particles so- lidified in this conventional manner have been studied by Rohatgi (1), who observed that the nucleation of liquid metal frequently occurs away from the surface of the re- inforcement. Composites produced in this manner are be- lieved to have inferior material properties. One possible way to improve the microstructure is to extend the ends of the reinforcing phase outside the casting mold and cool the ends of the fibers by a heat sink. Since a faster heat extraction is introduced, the solidification time can be shortened. This process of cooling the fiber ends during processing of composites is referred to as thermal man- agement of fibers. Rohatgi et al. (2) investigated the solidification of aluminum alloys which had graphite cylinders extending outside the solidifying melt, and were put in a lower tem- perature environment to promote heat transfer through the graphite rod. Solidification microstructure of MMC has demonstrated that upon solidification, dispersoids gener- ally tend to segregate in the boundaries of pro-eutectic - Al dendrites (3-5), thereby diminishing the properties of these materials. Generally, one would expect that during solidification, the dispersed particles should act as prefer- ential sites for heterogeneous nucleation of the solidifying primary phase. A large number of observations by differ- ent research groups confirm that in aluminum base alloys, aluminum dendrites do not nucleate on the surfaces of dispersoids like graphite and silicon carbide. However, if nucleation of different phases on these reinforcements can be controlled, then the properties will be enhanced due to avoidance of particle segregation and a variety of interfaces between the dispersoids and the matrix can be generated, leading to tailor-made properties. Experiments in which the ends of the cylindrical rods are cooled, indicate altered microstructures at the inter- faces between matrix and the cylindrical rods as well as in the matrix. The alterations in the interfacial structure due to cooling of the ends of cylinders are attributed to changes in the local temperature differences at the inter- face between cylinders and the matrix during solidifica- tion. These observations suggest that thermal manage- ment can significantly change the nature of the interface and the matrix and therefore, the properties of cast com- posites.

Effect of Thixoforming Process and Microstructural Changes in the A380 Matrix Composite Reinforced with NbC by the Stir Casting Method

Microstructures, Mechanical Properties and Thixoformability of TiB 2 /Al Composite Prepared by Ultrasonic-Assisted Squeeze Casting

Mechanical Behaviour and Morphology of Thixoformed Aluminium Alloy Reinforced by Graphene

Effect of Remelting Temperature and Soaking Time on Microstructure and Mechanical Properties of the Thixoformed Part of Nano-Sized SiCp/7075 Composite

Integrated Manufacturing of Powder Metallurgy Preparation-Thixoforming for Al0.8Co0.5Cr1.5CuFeNi HEA: Excellent Formability and Enhancement by In-Situ Generated Al2O3 in Liquid Phase

Effects of Forming Temperature, Soaking Time and Dwell Time on the Microstructure and Mechanical Properties of Thixoformed Nickel-Based Superalloy Parts

Microstructure and Mechanical Properties of Nickel-Based Superalloy GH4037 Parts Formed by Thixoforming

Feasibility of Al/Al_2O_3 Composite Thixoforming in Pseudo-semi-solid State

Microstructure evolution and tensile mechanical properties of thixoformed high performance Al-Zn-Mg-Cu alloy

Synthesis of TiAl/Nb Composites with Concurrently Enhanced Strength and Plasticity by Powder Metallurgy

Thixoforming-forging compound forming technology for 6A02 Al bracket-shape component

Effect of Short Heat Treatments on the Microstructural Evolution and Hardness of Thixoformed Graphene Reinforced Aluminium Composites

Effect of mechanical conditions on the microstructures and mechanical properties of thixoformed Al-Cu-Si-Mg alloy

Thixo-die-forging of Al/Al2O3 Composite in Pseudo-Semi-solid State and Toughening-Strengthening

Unraveling Solid–liquid Phase Transition and Microstructural Coarsening of Semi-Solid Al0.8Co0.5Cr1.5CuFeNi HEA with Dual Globules for Thixoforming Application

The Effect of Initial Microstructure of A356 Alloys on the Mechanical Behavior in the Semisolid State

Ceramics Matrix Composites Thixoforming in Pseudo-Semi-solid State and the Preliminary Experimental Study

Thermal Management of Metal Matrix Composite Solidification

Semi-solid processing of the primary aluminium die casting alloy A365

The effect of Cu–8%P master alloy, SIMA process, thixoforming, and heat treatment on the microstructure and mechanical properties of Al–20%Mg 2 Si composite

Effect of Casting and Additive Manufacturing on the Microstructure and Mechanical Property of Al-Cu Composites