Abstract:In this study, the GMAW welding torch was controlled by a stepping motor to achieve a periodic swing. By controlling the swing speed, a micro-variable deposition path was obtained, which was called the micro-control deposition trajectory. The influence of the micro-control deposition trajectory on the arc characteristics, microstructure, and mechanical properties of 304 steel wire arc additive manufacturing was studied. The results showed that the micro-control deposition process was affected by the swing arc and the deposition trajectory and that the arc force was dispersed over the whole deposition layer, which effectively reduced the welding heat input. However, the arc centrifugal force increased with the increase in the swing speed, which easily caused instability of the arc and large spatter. Compared with common thin-walled deposition, the deposition width of micro-control thin-walled deposition components was increased. In addition, the swinging arc had a certain stirring effect on the molten pool, which was conducive to the escape of the molten pool gas and refinement of the microstructure. Below, the interface of the deposition layer, the microstructure of the common thin-walled deposition components, and the micro-control thin-walled deposition components were composed of lathy ferrite and austenite. Compared with the common deposition, when the swing speed increased to 800 °/s, the microstructure consisted of vermicular ferrite and austenite. The tensile strength and elongation of the micro-control thin-walled deposition components are higher than those of the common thin-walled deposition components. The tensile fracture mechanism of the common thin-walled deposition components and the micro-control thin-walled deposition components was the ductile fracture mechanism.

Effect of Different Wire Feeding Strategies on the Preparation of Functionally Graded Materials by Dual-Wire Arc Additive Manufacturing

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Effect of composition gradient design on microstructure and mechanical properties of dual-wire plasma arc additively manufactured 316L/IN625 functionally graded materials

Research on Transition Layer Microstructure and Properties of Al–Cu/Al–Si Gradient Materials Fabricated by Cold Metal Transfer

Effect of twin-wire feeding methods on the in-situ synthesis of electron beam fabricated Ti-Al-Nb intermetallics

Influence of Auxiliary Process on Microstructure and Mechanical Properties of Wire Arc Additive Manufacturing of Thick Wall Depositions

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Effect of Deposition Strategies on Microstructures, Defects and Mechanical Properties of 5356 Aluminum Alloy by Wire Arc Additive Manufacturing

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Effects of Deposition Paramaters on the Microstructure Evolution of Wire Arc Additive Manufactured Al–Zn–Mg–Cu Alloy

Effect of Laser Scanning and Powder Addition on Microstructure and Mechanical Properties for Hot-Wire-Feed Laser Additive Manufacturing

A Novel Preparation Approach of Aluminum-Based Functionally Graded Material: Auxiliary Wire Filling Gas Metal Arc Directed Energy Deposition

Fabrication of Fe-FeAl Functionally Graded Material Using the Wire-Arc Additive Manufacturing Process

Mathematical analysis and process optimization of wire and arc additive manufactured Ti6Al4V ELI alloy with in-situ rolling

Grain Morphology Evolution Mechanism of Titanium Alloy by the Combination of Pulsed Arc and Solution Element During Wire Arc Additive Manufacturing

Improvement in Microstructure and Properties of 304 Steel Wire Arc Additive Manufacturing by the Micro-Control Deposition Trajectory

Microstructure regulation of titanium alloy functionally gradient materials fabricated by alternating current assisted wire arc additive manufacturing

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Microstructure transformation and mechanical behavior in NiTi alloys fabricated by dissimilar double wires arc additive manufacturing

Influence of Heat Flow on the Grain Morphology and Porosity of Wire Arc Additive Manufactured 2319 Aluminum Alloy

Numerical Analysis on the Effect of Process Parameters on Deposition Geometry in Wire Arc Additive Manufacturing