Abstract:Non-grain oriented electrical steels (NGOES) are typically used in electric applications with rotating magnetic fields and thus essential for the production of electric motors. The increasing number of electric vehicles results in a growing demand for electrical steel sheets used in the stacked laminations of rotor and stator components. E-mobility applications require the best possible magnetic properties for optimum performance and efficiency, especially at high frequencies. In addition, increased mechanical strength is necessary to withstand the centrifugal forces resulting from high revolution speeds. Chemical composition, microstructure and crystallographic texture strongly influence the magnetic properties, whereas the mechanical properties are mainly affected by the chemical composition and grain size. Optimizing the texture is a possible method for improving the magnetic properties without significantly compromising the mechanical strength. In this work a special processing route for the production of 3.25% Si NGOES sample material has been studied, using laboratory cold rolling and annealing facilities. Compared to the classical processing route of single stage cold rolling and annealing, this alternative method involves two cold rolling steps with an intermediate annealing treatment between the first and second rolling sequence and a final annealing treatment after the second rolling step. The samples were produced with different intermediate thicknesses, changing the amount of cold rolling deformation of each sample variation. The degree of deformation affects the recrystallization and grain growth behavior and thus the resulting microstructure and texture. The microstructural and textural evolution was investigated in the hot rolled, intermediate annealed and final annealed state using electron backscatter diffraction (EBSD). Finished samples were additionally examined using magnetic testing and tensile testing. The results indicate a correlation between the intermediate thickness and the final grain size of the steel samples. Furthermore, the highly grain size dependent mechanical strength and magnetic losses are influenced. EBSD-data were used to interpret the texture and to calculate a parameter describing the magnetic quality of the texture. The results show a strong improvement of magnetically favorable texture components along with increasing intermediate thickness, enabling significantly better polarization values in rolling direction and transversal direction. However, anisotropy of the magnetic properties increases as well due to the textural changes.

A study of Laves phase in high Nb non-oriented silicon steel for electric automobiles

Influence of Annealing Process on Microstructures,Mechanical and Magnetic Properties of Nb-Containing High-Strength Non-Oriented Silicon Steel

A comprehensive study on texture evolution and recrystallization mechanism of Fe-4.5 wt% Si with strong {114}

Influence of Nb Content on Precipitation, Grain Microstructure, Texture and Magnetic Properties of Grain-Oriented Silicon Steel

The impact of niobium on the microstructure, texture and magnetic properties of strip-cast grain oriented silicon steel

Microstructure Characteristics and Strengthening Behavior of Cu-Bearing Non-Oriented Silicon Steel: Conventional Process versus Strip Casting

Characterization of microstructure, texture and magnetic properties in twin-roll casting high silicon non-oriented electrical steel

The effect of Nb content on precipitates, microstructure and texture of grain oriented silicon steel

Fabrication of high-performance low silicon non-oriented electrical steels by a new method: Low-finishing-temperature hot rolling combined with batch annealing

Phase precipitation behavior of rapidly quenched ternary La–Fe–B alloy and the effects of Nd substitution

Development of Λ-Fiber Recrystallization Texture and Magnetic Property in Fe–6.5wt% Si Thin Sheet Produced by Strip Casting and Warm Rolling Method

EFFECT OF COLD ROLLING PROCESS ON TEXTURE EVOLUTION OF GRADIENT MICROSTRUCTURE IN Fe-3,0 % Si NON-ORIENTED SILICON STEEL

Micro Characterization of Hot-Rolled Plate of Nb-Bearing Grain-Oriented Silicon Steel

Study on microstructure and texture of a new-type low Si high Mn non-oriented silicon steel 50W250

Microstructure and texture evolution of ultra-thin high grade non-oriented silicon steel used in new energy vehicle

Development of thin-gauge low iron loss non-oriented silicon steel

Microstructural and textural evolution of double stage cold rolled non-grain oriented electrical steel

Improvement of magnetic properties via normalizing annealing for high-strength Fe-4.5wt.%Si electrical steel

Microstructure and texture evolution of thin-gauge non-oriented silicon steel with high permeability produced by twin-roll strip casting

Tracing the recrystallization of warm temper-rolled Fe–6.5 wt% Si non-oriented electrical steel using a quasi in situ EBSD technique