Abstract:For recent lithium-ion batteries (LIBs), there have been lots of researches about convert liquid-phase electrolyte to solid-state electrolyte (i. e. all-solid-state battery) to improve safety and stability. Solid-state electrolyte materials have to satisfy some criteria including high ionic conductivity at room-temperature, chemical stability against reducing environment, and mechanical strength. Many solid-materials for electrolyte have been researched, including perovskite, garnet, and sulfide-type of materials. Among them, garnet-type based lithium lanthanum zirconium oxide (LLZO, Li 7 La 3 Zr 2 O 12 ) has been received attention due to its high ionic conductivity (~10 -4 S/cm at room temperature) and wide electrochemical stability window (~6 V versus Li/Li + ). The main issue of LLZO is the high interfacial resistance with anode and cathode materials such as Li metal and LiCoO 2 . Many researchers have tried to understand the cause of this interfacial resistance for LLZO. K. Park et al. researched about the cathode/electrolyte (LLZO) interface and revealed co-diffusion and second-phase formation of LLZO at high-temperature [1]. M. Zarabian et al. reported that spin-coated LLZO on the LiCoO 2 pellet fabricated at low-temperature (~400 o C) and co-diffusion of La and Co at the interface by using X-ray photoelectron spectroscopy (XPS) [2]. They commonly suggested that elevated temperature make chemical interaction and this make high interfacial resistance. In this study, we adopted novel sintering method, flash light annealing (FLA) process, to fabricate LLZO solid-electrolyte. This method is also called rapid, cool sintering because of its unique characteristics compared to conventional sintering methods [3]. FLA uses instantaneous high current to generate intensive pulsed light (IPL), and irradiate IPL toward the specimen to sinter the materials. Unlike the conventional sintering methods, this novel method has lots of advantages including availability of treatment at STP and fast sintering time (~ a few ms). Rapid sintering process gives no time for the diffusion at the interface, thus the interfacial resistance between cathode and LLZO solid-electrolyte must be reduced. We fabricated LLZO solid-electrolyte on the commercial LiCoO 2 pellet by using solution-based spin-coating method and sintered the film by using FLA method. XPS and energy-dispersive X-ray spectroscopy (EDX) analysis were conducted to observe interface and diffusion of La and Co elements. Also, X-ray diffraction (XRD) method was used to investigate sintering ability of FLA through crystallinity development. The interfacial resistance between LiCoO 2 and LLZO solid-electrolyte was analyzed by electrochemical impedance spectroscopy (EIS) through cross-plane set-up.

Analyzing void formation and rewetting of thin in situ-formed Li anodes on LLZO

Li Stripping Behavior of Anode‐Free Solid‐State Batteries Under Intermittent‐Current Discharge Conditions

Operando Characterization of Plating and Stripping Dynamics of Li-Mg Alloy Anode and Sulfide Solid Electrolyte Interface

Nanoscale Visualization of Lithium Plating/Stripping Tuned by On‐site Formed Solid Electrolyte Interphase in All‐Solid‐State Lithium‐Metal Batteries

Assessment of Critical Stack Pressure and Temperature in Li‐Garnet Batteries

Interfacial Stability of Li Metal-Solid Electrolyte Elucidated Via in Situ Electron Microscopy.

Reducing Impedance at a Li-Metal Anode/Garnet-Type Electrolyte Interface Implementing Chemically Resolvable In Layers

In Situ Analysis of Interfacial Morphological and Chemical Evolution in All‐Solid‐State Lithium‐Metal Batteries

Interface Engineering Enabling Thin Lithium Metal Electrodes Down to 0.78 Μm for Garnet-Type Solid-State Batteries

osure and surface chemistry on Li – Li 7 La 3 Zr 2 O 12 interfacial resistance †

Impact of Air Exposure and Surface Chemistry on Li-Li7la3zr2o12 Interfacial Resistance

One-Step Processing of Soft Electrolyte/Metallic Lithium Interface for High-Performance Solid-State Lithium Batteries

Ultrahigh Areal Capacity Li Electrodeposition at Metal-Solid Electrolyte Interfaces under Minimal Stack Pressures Enabled by Interfacial Na-K Liquids

An in Situ-Formed LiI Interface Layer for Garnet-Based Lithium Metal Batteries

Evaluation of Porous Lithium Lanthanum Zirconium Oxide (LLZO) Anode Host Structures for Li-Metal Batteries

Fast Charge Transfer between LLZO Solid Electrolyte and LCO Cathode Thin Films with a Modified Interface

Toward a Fundamental Understanding of the Lithium Metal Anode in Solid-State Batteries—An Electrochemo-Mechanical Study on the Garnet-Type Solid Electrolyte Li 6.25 Al 0.25 La 3 Zr 2 O 12

In Situ Formed Surface Layer to Improve the Air Stability of LLZTO and Its Contact with the Li Metal

Interface Engineering for Garnet-Type Electrolyte Enables Low Interfacial Resistance in Solid-State Lithium Batteries

Regulation Mechanism on A Bilayer Li 2 O‐Rich Interface between Lithium Metal and Garnet‐Type Solid Electrolytes

A Study on Cathode Interface of Li-La-Zr-O Solid-State Electrolyte Fabricated Via Rapid Sintering Process