Abstract:Abstract Precision machining is becoming more and more important with the increasing demands on surface quality for various components. This applies, for example, to mirror components in micro-optics or cooling components in microelectronics. Copper is a frequently used material for this purpose, but its mechanical properties make it difficult to machine. In this study, a process strategy for finishing copper surfaces with batch-manufactured micro-grinding tools in an electrochemically assisted grinding process is demonstrated. The tool heads are manufactured from a polyimide-abrasive-suspension and silicon as a carrier substrate using microsystems technology. The matching shafts are milled from aluminium. The tools are then used on pure copper and oxidised copper surfaces. By using finer abrasives grains (1.6–2.4 μm instead of 4–6 μm) than previously, similar surface roughness values could be achieved ( R a = 0.09 ± 0.02 μm, R z = 1.94 ± 0.73 μm) with the same grinding process. An optimised grinding process that combines the use of rough and fine tools, on the other hand, achieves significantly better surface finishes in just four grinding iterations ( R a = 0.02 ± 0.01 μm, R z = 0.83 ± 0.21 μm). In order to achieve a further increase in surface quality, this optimised grinding process is combined with the anodic oxidation of the copper workpieces. The surface modification is done to increase the machinability of the surface by creating an oxide layer. This is confirmed by the results of scratch tests carried out, which showed less force acting on the tool during machining with the oxide layer than with a pure copper surface. To realise this within the machine tool, an electrochemical cell is shown that can be integrated into the machine so that the oxidation can be carried out immediately before the grinding process. The copper layers produced inside the electrochemical cell in the machine tool show similar characteristics to the samples produced outside. Processing the oxidised samples with the optimised grinding process led to a further reduction of about 17% in the R z values ( R a = 0.03 ± 0.01 μm, R z = 0.69 ± 0.20 μm). The combination of the shown grinding process and the integration of anodic oxidation within the machine tool for the surface modification of copper workpieces seems to be promising to achieve high surface finishes.

Finishing of OFHC copper using fluid filled open-cell porous flexible abrasive impregnated tools

Numerical and experimental investigation into tool-workpiece interaction in flexible abrasive tool finishing

Detailed characterisation of batch-manufactured flexible micro-grinding tools for electrochemical assisted grinding of copper surfaces

Synthesis of polishing fluid and novel approach for nanofinishing of copper using ball-end magnetorheological finishing process

A Low Cost and Residue-Free Abrasive-Free Copper Cmp Process with Low Dishing, Erosion and Oxide Loss

Atomic-level flatness on oxygen-free copper surface in lapping and chemical mechanical polishing

Selection of optimum polishing fluid composition for ball end magnetorheological finishing (BEMRF) of copper

Towards obtaining high-quality surfaces with nanometric finish by femtosecond laser ablation: A case study on coppers

Precision Fabrication of Thin Copper Substrate by Double-sided Lapping and Chemical Mechanical Polishing

Preparation of Flat and Smooth Copper Surface by Jet Electrochemical Machining and Electrochemical Polishing

Copper chemical mechanical polishing using a slurry-free technique

High-precision laser powder bed fusion processing of pure copper

Development of a magnetically driven abrasive polishing process for additively manufactured copper structures

Experimental study of rectangular-curved magnet–based magnetorheological finishing tool for copper cylindrical workpiece

Novel Disc Hydrodynamic Polishing Process and Tool for High-Efficiency Polishing of Ultra-Smooth Surfaces

Facile Fabrication of Durable Copper-Based Superhydrophobic Surfaces via Electrodeposition

Improved approach to magnetorheological finishing of blind-hole cavities

Investigations on flexible pad polishing for nano-finishing of freeform optics mold

Tailoring the wettability of surface-textured copper using sub-THz bursts of femtosecond laser pulses

Investigation on Magnetorheological Finishing of thin Copper Substrate

An overview of magnetorheological polishing fluid applied in nano-finishing of components