Abstract:The present investigation has employed recycled waste glass powder (WGP) and silicon nitride (Si 3 N 4 ) as reinforcing-agents within AZ91D-matrix composites. The composites were fabricated by employing the vacuum stir casting technique to mitigate the effects of oxidation and to ensure homogeneity, uniformity, and superior wettability among the AZ91D-matrix and reinforcements. A microscopic study provided confirmation of a uniform dispersion of WGP and Si 3 N 4 particles throughout the AZ91D-matrix. The tensile strength of the AZ91D/WGP/Si 3 N 4 composites rise with the inclusion of WGP particulates by up to 1.5 percent in AZ91D/7.5% Si 3 N 4 . However, the tensile strength of the AZ91D/9%Si 3 N 4 composite have showed maximum value as compared to other chosen formulations/combinations in the current investigation. The tensile strength of AZ91D/1.5% WGP/7.5% Si 3 N 4 composites has strengthened up to 12.13 percent with the comparison of base alloy AZ91D-matrix. In A1 formulated composite, the amount of WGP particulate has enhanced the hardness of the AZ91D-alloy by up to 1.5 percent. Findings, nevertheless has exhibited that the A6 formulated composite had superior outcomes in terms of hardness. The incorporation of "reinforcing-constituent particulates" with 1.5%WGP + 7.5%Si 3 N 4 combination within the AZ91D-matrix, has further increased fatigue-strength by around 57.84 percent. A weight-loss of 0.312 mg was being unveiled for the A1 formulated fabricated composite. The weight-loss for the A6 formulated fabricated composite, however, was reported to be 0.294 mg. At 5 N loads, 2 m/s sliding speed, and 1000 m of sliding distance, the developed 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites was reported to have a rate of wear, and frictional coefficient of 0.0025 mm 3 /m and 0.315, respectively. The investigation employing scanning electron microscopy (SEM) identified the presence of corrosion pits on the surfaces that had undergone corrosion. These pits were found to be a result of localised surface assaults occurring in corrosive environments. Additionally, SEM pictures of the worn surfaces indicated the emergence of microcracks, which may be associated to the conditions of cyclic loading. Moreover, the tensile-fractography examination for the developed 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites has exhibited the brittle fracture failure, including cracks and debonding phenomena. In addition, the EDS spectra-analysis have revealed an apparent existence of the observed Mg-peak, Si-peak, Al-peak, Ca-peak, and O-peak for the 1.5%WGP/7.5%Si 3 N 4 /AZ91D composites. Furthermore, the utilisation of X-ray diffraction analysis effectively determined the existence of hard phases inside the AZ91D-matrix, which significantly contributed to the reported enhancement in wear resistance. The development of harder-phases has included, α-Mg, Al 12 Mg 17, SiO 2 , Si 3 N 4 , MgO, and CaO phases within the composite has been accountable for the enhancement of the tribomechanical, and wear-resistance characteristics of the AZ91D/WGP/Si 3 N 4 composites. The Si 3 N 4 has been discovered to have a substantial impact on enhancing mechanical performance and raising the resistance to wear.

Utilization of Silicon from Lemongrass Ash Reinforcement with ADC 12 (Al-Si alloy) Aluminium on Mechanical and Tribological Properties

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Taguchi-based Grey Relational Analysis for multi-response optimization of the characteristics of HRAMMCs reinforced with agro-waste and SIC produced by ultrasonic-assisted bottom pour two-stage stir casting

Effects of Rice Husk Ash and Silicon Carbide addition on AA6351 Hybrid Green Composites

Mechanical, dry sliding wear and tensile fatigue behaviour of rice hush ash–derived silicon carbide dispersed LM25 metal matrix composites

Exploring the effect of bio-silica on the mechanical, microstructural, and corrosion properties of aluminium metal matrix composites

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Influence of Silicon Carbide Reinforcements on Mechanical and Wear Behaviour AA7075/15% wt. Glass fiber Hybrid Composites

Tribological Behavoiur of Silicon Carbide/ Rice Husk ash Reinforced Al7075 Hybrid Composites Using Optimization Techniques

Synthesis and characterization of spent alumina catalyst and grinding sludge reinforced aluminium-based composite material

Fractography and Tensile Properties of AA6061 Aluminium Alloy/Rice Husk Ash Silicon Nanocomposite

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)

Enhancing tribo-mechanical, microstructural morphology, and corrosion performance of AZ91D-magnesium composites through the synergistic reinforcements of silicon nitride and waste glass powder

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Mechanical Test on Aluminum Alloy with Maximal Soluble SiC Reinforcement

Investigating the tribological behavior of bioinspired surfaces in agro-waste and alumina reinforced AA6063 matrix composites

Effect of forging on mechanical properties of rice husk ash-silicon carbide reinforced Al1100 hybrid composites

Experimental investigation in enhancing the mechanical, wear and corrosion resistance properties of Al6061-SiC-NSA composites fabricated using stir casting process.

Rice Husk Ash as Pore Former and Reinforcement on the Porosity, Microstructure, and Tensile Strength of Aluminum MMC Fabricated via the Powder Metallurgy Method

The utilization of agricultural and industrial waste in the synthesis of AA7075-based novel lightweight composite

Investigation on Mechanical Properties of Agro and Industrial Waste Reinforcement in Aluminium 7075 Composite with Liquid Metal Stir Casting Route