Abstract:Although defect engineering is the core strategy to improve thermoelectric properties, there are limited methods to effectively modulate the designed defects. Herein, we demonstrate that a high ZT value of 1.36 at 775 K and a high average ZT value of 0.99 in the temperature range from 300 to 825 K are realized in Zn-containing PbTe by designing complex defects. By combining first-principles calculations and experiments, we show that Zn atoms occupy both Pb sites and interstitial sites in PbTe and couple with each other. The contraction stress induced via substitutional Zn on Pb sites alleviates the swelling stress by Zn atoms occupying the interstitial sites and promotes the solubility of interstitial Zn atoms in the structure of PbTe. The stabilization of Zn impurity as a complex defect extends the region of PbTe phase stability toward Pb0.995Zn0.02Te, while the solid solution region in the other direction of the ternary phase diagram is much smaller. The evolution of defects in PbTe was further explicitly corroborated by aberration-corrected scanning transmission electron microscopy (Cs-corrected STEM) and positron annihilation measurement. The Zn atoms compensate the Pb vacancies (VPb) and Zn interstitials (Zni) significantly improve the electron concentration, producing a high carrier mobility of 1467.7 cm2 V–1 s–1 for the Pb0.995Zn0.02Te sample. A high power factor of 4.11 mW m–1 K–2 is achieved for the Pb0.995Zn0.02Te sample at 306 K. This work provides new insights into understanding the nature and evolution of the defects in n-type PbTe as well as improving the electronic and thermal transport properties toward higher thermoelectric performance.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c14518.Experimental section, backscattering electron images, wavelength dispersive spectrometer results, electrical and thermal transport performance of the Pb1–yZnyTe samples, and room-temperature carrier mobility as a function of carrier concentration for the Pb1–yZn0.015+yTe samples and several n-type PbTe compounds (PDF)This article has not yet been cited by other publications.

Improved High‐Temperature Material Stability and Mechanical Properties While Maintaining a High Figure of Merit in Nanostructured p‐Type PbTe‐Based Thermoelectric Elements

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Improving the Long-Term Stability of PbTe-Based Thermoelectric Modules: From Nanostructures to Packaged Module Architecture

Enhanced thermoelectric performance of n-type Nb-doped PbTe by compensating resonant level and inducing atomic disorder

High-performance in n-type PbTe-based thermoelectric materials achieved by synergistically dynamic doping and energy filtering

Modulating the Valence of Ga and the Deep Level Impurity for High Thermoelectric Performance of N-Type Pb0.98Ga0.02Te1-xSex Compounds

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

Enhancing n-type PbTe thermoelectric performance through Cd alloying and strategic defects management

Enhanced Thermoelectric Performance of N‐Type PbSe Through Semi‐Coherent Nanostructure by AgCuTe Alloying

Achieving higher thermoelectric performance of n-type PbTe by adjusting band structure and enhanced phonons scattering

Zn-Induced Defect Complexity for the High Thermoelectric Performance of n-Type PbTe Compounds

Enhanced Thermoelectric Performance of N-Type PbTe Through the Introduction of Low-Dimensional C60 Nanodots

High thermoelectric performance of p-type SnTe via a synergistic band engineering and nanostructuring approach

Enhanced Thermoelectric Performance of P‐Type (Bi,Sb)2Te3 by Incorporating Non‐Stoichiometric Ag5Te3 and Refining Te‐Se Ratio

Achieving High-Performance N-Type PbTe Via Synergistically Optimizing Effective Mass and Carrier Concentration and Suppressing Lattice Thermal Conductivity

Valence Band Modification and Enhanced Phonon‐Phonon Interactions for High Thermoelectric Performance in GeTe

Hierarchical Architectural Structures Induce High Performance in n‐Type GeTe‐Based Thermoelectrics

Thermoelectric enhancement at low temperature in nonstoichiometric lead-telluride compounds

Pseudo‐Nanostructuring and Grain Refinement Enhance the Near‐Room‐Temperature Thermoelectric Performance in n‐type PbSe

Realizing High-Performance Thermoelectric Modules Through Enhancing the Power Factor Via Optimizing the Carrier Mobility in N-Type PbSe Crystals

Nanostructure and High Thermoelectric Performance in Nonstoichiometric AgPbSbTe Compounds: the Role of Ag