Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

Screening and Testing of Anti-Slagging Agents for Tobacco-Stalk-Based Biomass Pellet Fuel for Tobacco Curing

The Application of Biomass Fuel Substituting Coal in Tobacco Curing

Reduced Pollutant Emissions and Slagging Rate of Biomass Pellet Combustion by Optimizing the Multilayer Distribution of Secondary Air

Effects of torrefaction on ash-related issues during biomass combustion and co-combustion with coal. Part 3: Ash slagging behavior

Control of Pollutants in the Combustion of Biomass Pellets Prepared with Coal Tar Residue As a Binder

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Behavior of Slagging Deposits During Coal and Biomass Co-combustion in a 300 Kw Down-Fired Furnace

Effects of additives blended in corn straw to control agglomeration and slagging in combustion

Slagging inhibition through co-firing of coal gangue and high sodium coal: An experimental and modelling study

Dried sludge reburning blended with calcium magnesium acetate addition in a fluidized bed combustor

Experiment Study on Ash Fusion Characteristics of Cofiring Straw and Sawdust

Mechanical Strength and Combustion Properties of Biomass Pellets Prepared with Coal Tar Residue As a Binder

Study on Fusion Characteristics of Biomass Ash

Experimental and numerical techniques to evaluate coal/biomass fly ash blend characteristics and potentials

Investigation on Ash Slagging Characteristics During Combustion of Biomass Pellets and Effect of Additives

Pelletization of Post-Harvest Tobacco Waste and Investigation of Flue Gas Emissions from Pellet Combustion

Effects of Inorganic Additives on Slagging Characteristics of Peanut Shell Pellet Fuel

Experimental Study on Ash Fusion Characteristics and Slagging Potential Using Simulated Biomass Ashes

Experimental Evaluation of Additives and K2O–SiO2–Al2O3 Diagrams on High-Temperature Silicate Melt-Induced Slagging During Biomass Combustion

An optimized heating source for heat-not-burn tobacco products through synergistic combustion of tobacco stalk and graphite carbon with K2CO3 catalyst

Experimental Study on Ash Morphology, Fusibility, and Mineral Transformation During Co-Combustion of Antibiotic Filter Residue and Biomass