Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

Experimental and numerical techniques to evaluate coal/biomass fly ash blend characteristics and potentials

Characteristics Experimental of Fly Ash Release in Combustion Process of Blended Coal

Thermal Studies of Fractionated Lignite and Brown Coal Fly Ashes

Optimization of low-grade coal and refuse-derived fuel blends for improved co-combustion behavior in coal-fired power plants

Study on chemical characteristics of coal and biomass blend and the tendency of its ash deposition

Utilization of Fly Ashes from Fluidized Bed Combustion: A Review

Investigation on Effect of Coal Fly Ash on Properties of Corn Straw Pyrolysis Products

Waste to concrete material: Potential Study of Chemical Characterization of Coal Fly Ash and Bottom Ash

Bio-modification and application of coal fly ash in cementitious composites

Influence Of Coal Blending On Ash Fusibility In Reducing Atmosphere

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Effect of the Coal Fly Ash Blending Ratio on Biomass Slagging Structure Modification and Alkali Metal Migration

Effective utilization of Coal Fly Ash (CFA): perspectives and opportunities in various industrial sectors and hydrocarbon extraction processes

The use of fractionated fly ash of thermal power plants as binder for production of briquettes of coke breeze and dust

Comparative Analysis of Woody Biomass Fly Ash and Class F Fly Ash as Supplementary Cementitious Materials in Mortar

Experiment and Kinetics Studies on Ash Fusion Characteristics of Biomass/Coal Mixtures During Combustion

Strength Characteristics and Rheological Behavior of a High Level of Fly Ash in the Production of Concrete

Comparative Analysis of Coal and Biomass for Sustainable Energy Production: Elemental Composition, Combustion Behavior and Co-Firing Potential

Research on the effect of recombustion treatment on the performance of straw biomass fly ash

Fly Ash Application as Supplementary Cementitious Material: A Review

Mechanical Activation of Fly Ash from MSWI for Utilization in Cementitious Materials.