Abstract:A method for the opening of silicon-containing technogenic feedstock using an aqueous solution of ammonium bifluoride (NH4HF2) with subsequent production of amorphous silica has been developed. In this work we examined wet magnetic separation tailings (WMST) – iron titanium-magnetite ore enrichment rejects that are formed in huge quantities and stored in sludge depositories at concentrating plants. The main rock-forming minerals of WMST are resistant silicates – pyroxene, amphibole, plagioclase and olivine with the total SiO2 content of about 50%. It was established that fluorination of silicon-containing minerals begins during mechanical dispersion of a dry reaction mixture at room temperature. The thermodynamic calculations confirm active interaction of components in the composition of mineral complexes already at 25 °C, some of the processes being exothermic with entropy reserve. When the temperature increases to 90 °C and the duration of leaching to 5 h, the extraction of silicon in the form of soluble ammonium fluorosilicate grows. Insoluble calcium and magnesium fluorides and sparingly soluble under leaching conditions ammonium fluorometallates, as well as a part of unreacted rock are formed in the insoluble residue. Under the most effective desilication conditions (20% NH4HF2 solution, L:S=4:1, 2 h), the residual content of SiO2 decreases to 1–2%. The synthesis of finely dispersed amorphous silica (SiO2) was performed by hydrolytic deposition when the value of рН of clarified ammonium fluorosilicate solution was reduced by adding ammonia. It was shown that gradual introduction of hydrous ammonia (5 ml/h) into diluted fluorosilicate solution with a concentration of less than 5 g/l Si while constant stirring leads to the formation of spherical silica nanoparticles. The degree of silica extraction from tailings in the process of hydrofluorination of 20% NH4HF2 solution at 90 °C for 2 h was 98%, and the content of impurities in amorphous silica did not exceed 1–2%. Separation of finely dispersed suspension of insoluble fluorides and hydroxide impurities formed during stepwise hydrolysis of fluorosilicate solution to рН value less than 5 is a necessary condition for producing pure silica SiO2. The final product, similar to “white soot” in properties, is characterized by predominant particle size in the interval of 2-20 nm, a large surface area 230-360 m2/g and a low pycnometric density 1.62 g/cm3. For citation: Medyankina I.S., Pasechnik L.A. Hydrofluoride processing of tailings from wet magnetic separation of titanomagnetite to obtain amorphous silicon dioxide. ChemChemTech [Izv. Vyssh. Uchebn. Zaved. Khim. Khim. Tekhnol.]. 2023. V. 66. N 2. P. 70-77. DOI: 10.6060/ivkkt.20236602.6706.

Fluoroammonium Method for Titanium Slag Processing

Fluorammonium method of titanium slag processing

Fluoroammonium method for processing of cake from leaching of titanium-magnesium production sludge

A novel process for preparation of titanium dioxide from Ti-bearing electric furnace slag: NH4HF2-HF leaching and hydrolyzing process

High-Titanium Slag Preparation Process by Carbothermic Reduction of Ilmenite and Wet-Magnetic Separation

Studies on the Processing of Fine Dusts from the Electric Smelting of Ilmenite Concentrates to Obtain Titanium Dioxide

Recent Progress in Electric Furnace Titanium Slag Processing and Utilization: A Review

A novel preparation of titanium dioxide from titanium slag

Novel Process for Titanium Dioxide Production from Titanium Slag: NaOH-KOH Binary Molten Salt Roasting and Water Leaching

A study on the recovery of titanium from hydrofluoric acid leach solution of ilmenite sand

Extraction of vanadium and enrichment of titanium from modified Ti-bearing blast furnace slag

Extraction of Valuable Metals from Titanium-bearing Blast Furnace Slag by Acid Leaching

Technological Study of Titanium Slag Production from Titanium-Bearing Blast Furnace Slag

Technological research of process for producing titanium rich slag and complex titanium-containing ferroalloy

Composition and Properties of Titanium-Containing Blast Furnace Slags

Anti-caking in the production of titanium dioxide using low-grade titanium slag via the NaOH molten salt method

Preparation of rutile titanium dioxide pigment from low-grade titanium slag pretreated by the NaOH molten salt method

Extraction of valuable metals from Ti-bearing blast furnace slag using ammonium sulfate pressurized pyrolysis–acid leaching processes

Fundamental Study on Utilization of Titanium Resources by RHF Process

HYDROFLUORIDE PROCESSING OF TAILINGS FROM WET MAGNETIC SEPARATION OF TITANOMAGNETITE TO OBTAIN AMORPHOUS SILICON DIOXIDE