Abstract:In this paper, the finite volume method is used to investigate the laminar forced convection of water–copper nanofluid between two porous horizontal concentric cylinders. The effects of Reynolds number, the volume fraction of nanoparticles, the geometry, and the porous medium porosity on heat transfer have been studied. The problem is investigated in two different geometries and Re = 10, 25, 50, 75,100, and volume fraction of nanoparticles 0, 0.2, 0.5, 2, and 5% that were related to Copper nanoparticles and the porous medium porosity of 0.5, 0.9. The results indicated that in each geometry, the corresponding Nusselt number increase in the porosity of 0.9 is greater than that of the case with the porosity of 0.5. The results show that the increase in the heat transfer coefficient in the second geometry is greater than the first geometry and in porosity 0.9 is greater than porosity 0.5. These increase values are 6 and 3%, respectively. The increase in the average temperature of the inner cylinder surface in the five mentioned Reynolds values and both geometries is investigated. This increase in temperature in Re = 10 is greater than other Reynolds numbers. The corresponding temperature increases of Re = 10, for the first and second geometries, are 1.8 and 2.2%, respectively. Investigation of the effects of volume fraction of nanoparticles on Nusselt number and heat transfer coefficient shows that both parameters increase by increasing in the volume fraction of nanoparticles. The results show that the increase in the volume fraction of nanoparticles causes the increase in average temperature of the surface. The results show that these increases of temperature that take place in the volume fractions of 0.5, 2, and 5% of nanoparticles are equal to 0.6, 1.14, and 2.3% and relative to the water, respectively.

Numerical investigation of heat transfer in a tube equipped with twisted tape with different angles and under constant heat flux with copper nanofluid and evaluation of the results obtained using perceptron artificial neural networks

Heat transfer assessment of turbulent nanofluid flow in a circular pipe fitted with elliptical-cut twisted tape inserts

Experimental study and neural network-based prediction of thermal performance of applying baffles and nanofluid in the double-pipe heat exchangers

Effect of twist ratio on the thermal-hydraulic behavior of an aluminum oxide/cupric oxide nanofluid heat exchanger

Evaluation of thermal performance factor by hybrid nanofluid and twisted tape inserts in heat exchanger

Numerical investigation of nanofluid laminar forced convection heat transfer between two horizontal concentric cylinders in the presence of porous medium

Thermal analysis of nanofluids flow in a double pipe heat exchanger with twisted tapes insert in both sides

Influence of the twisting and nano fluids on performance of a triangular double tube heat exchanger

Heat transfer and pressure drop of Al 2 O 3 /water nanofluid in conically coiled tubes: Experimental and artificial neural network prediction

Designing artificial neural network of nanoparticle diameter and solid–fluid interfacial layer on single‐walled carbon nanotubes/ethylene glycol nanofluid flow on thin slendering needles

Internal Flow Analysis of a Heat Transfer Enhanced Tube with a Segmented Twisted Tape Insert

Numerical Research on Convective Heat Transfer and Resistance Characteristics of Turbulent Duct Flow Containing Nanorod-Based Nanofluids

Numerical study of the effects of geometric parameters and nanofluid properties on heat transfer and pressure drop in helical tubes

An experimental investigation on heat transfer characteristics of graphite-SiO2/water hybrid nanofluid flow in horizontal tube with various quad-channel twisted tape inserts

Development of machine learning algorithm for assessment of heat transfer of ternary hybrid nanofluid flow towards three different geometries: Case of artificial neural network

Numerical evaluation of the heat transfer in a shell and corrugated coil tube heat exchanger with three various water‐based nanofluids

Numerical study on the thermal performance of the shell and tube heat exchanger using twisted tubes and Al2O3 nanoparticles

Analysis of efficiency and performance evaluation criterion of nanofluid flow within a tube enhanced with perforated triple twisted tape: A two-phase analysis

Enhancing thermal performance: a sophisticated analysis of CuO-water nanofluids and twisted tape inserts in tubular heat exchangers-a numerical study

Numerical investigation of thermal performance augmentation of nanofluid flow in microchannel heat sinks by using of novel nozzle structure: sinusoidal cavities and rectangular ribs