Abstract:Introduction. Structural materials, including materials made of heat-resistant and hard-to-work steels, are widely used in various branches of mechanical engineering. To increase the efficiency of manufacturing parts of thermal equipment from heat-resistant and hard-to-work steels, the technological method of cutting with preliminary plasma heating of the workpiece is used. There is also a technological method of cutting metals, including hard-to-process materials by ultrasonic turning. Proceeding from this, in order to increase the efficiency of plasma machining of hard-to-process materials, it is necessary to investigate the technological possibilities of using ultrasonic turning of hard-to-process materials during plasma machining. The purpose of the work: to investigate the wear of cutting tools when using ultrasound in the conditions of plasma-mechanical processing of parts made of hard-to-process materials. The paper investigates the features of the plasma-mechanical processing under ultrasonic cutting conditions and determines the wear values of carbide cutters VK8, T5K10 and T15K6 when processing steels of grades 20Cr13Ni18 and 20Cr25Ni20Si2(cast). And also the wear of these cutters was determined under the conditions of conventional turning of the same materials to compare the results of wear of the cutters in different processing conditions. The research method is to determine the linear wear of carbide cutters along the back surface with conventional, plasma-mechanical and plasma-mechanical cutting assisted with ultrasonic cutting using an instrumental microscope and visual estimation with a 10x magnifying glass. Results and discussion. The paper presents the results of experimental studies to determine the wear of cutting tools when processing heat-resistant steels of the 20Cr13Ni18 and 20Cr25Ni20Si2(cast) grades with carbide cutters of the VK8, T5K10 and T15K6 grades. Studies were carried out to determine the wear of carbide cutters as with conventional mechanical cutting, plasma-mechanical cutting, as well as plasma-mechanical cutting using ultrasound. The experiments were carried out when turning these materials on a modernized lathe mod.1A64. A rectifier with a controlled choke and a plasma torch mod.APR-403 are connected to the lathe; a plasma holder is placed on the lathe carriage. A semiconductor rectifier serves as a power source with a compressed electric arc of current. The arcing takes place between the cathode (plasma torch) and the anode (blank) at the point of the plasma-forming gas; compressed air passes through the nozzle channel of the plasma torch. During the experiments, the position of the plasma torch was adjusted relative to the part rotation axis. When conducting experiments on studying the wear of cutters under conditions of ultrasonic plasma-mechanical cutting, ultrasound was applied to the cutting edge using a device developed by the authors. When processing heat-resistant steels under the usual turning condition, processing modes were adopted: cutting speed V = 10 m/min, cutting depth t = 3...4 mm, longitudinal feed Sl = 0.31 mm/rev. It is found that when processing steel grade 20Cr13Ni18 by conventional cutting, the back surface of the carbide cutter made of T5K10 wears out to 1 mm in size within 10 minutes, and for the cutter made of VK8 – within 15 minutes. During plasma machining, the cutting speed and the feed rate were increased 2 times; the results of the wear of the cutters show that at the same time T5K10 wears out to 1 mm within 20 minutes, VK8 – within 25 minutes. Plasma-mechanical processing using ultrasound show that the carbide cutter T5K10 wears out by 0.50 mm in less than 50 minutes of cutting, and VK8 wears out by 0.35 mm. The same results are obtained when processing heat-resistant steel 20Cr25Ni20Si2(cast). Thus, the study of wear of carbide cutters in the processing of heat-resistant steels shows that the use of ultrasonic cutting in plasma-mechanical processing of steels can significantly reduce the amount of tool wear. The presented results confirm the prospects of using ultrasonic plasma-mechanical cutting of heat-resistant steels with blade tools.

Development of Equipment and Technology for Precision Air-Plasma Cutting of Plate Steel

Influence of high-energy impact during plasma cutting on structure and properties of surface layers of aluminum and titanium alloys

Research on Mechanized Plasma Gouging of Weldable Construction Steels

Features of ultrasound application in plasma-mechanical processing of parts made of hard-to-process materials

Research on water-air plasma cutting process of carbon steel

Surface Structure Formation in Plasma Cutting of Aluminum and Titanium Alloys Using Direct Current Straight and Reverse Polarity

Structure Formation in Surface Layers of Aluminum and Titanium Alloys during Plasma Cutting

Study of underwater plasma arc ignition and cutting process for surface nonconductive steel structures for offshore decommissioning

Optimization of process parameters in plasma arc cutting of commercial-grade aluminium plate

Study of Plasma Arc Underwater Penetration Processes in Steel Structures Covered with Non-conductive Materials

The Design of an Atmospheric Pressure Plasma Torch Used for Polishing Ultra-Smooth Surfaces

Feasibility study on tandem narrow gap GMAW of 65 mm thick steel plate

Experimental study of an oxygen plasma cutting torch: II. Arc–material interaction, energy transfer and anode attachment

Investigations of material hardness and structural changes in the heat-affected zone during plasma cutting

Analysis of a Feasibility Study of a Precision Grinding Process for Industrial Blades Used in the Cutting of Soft Tissues by a Prototype 5-Axis CNC Grinding Machine

Optimization of Masking Process of Steel Tube During Atmospheric Plasma Spraying, for Use in Serial Production

PLATE-EDGE PREPARATION WITH MODERN FLAME-CUTTING TECHNIQUES

The study on plasma-Mig hybrid arc behaviour and droplet transfer for mild steel welding

Analysis of the Process and Results of High-Pressure Abrasive Water Jet Multilayer Cutting of Electrical Steel

Performance optimization and investigation of metal-cored filler wires for high-strength steel during gas metal arc welding

The Design and Analysis of a Novel Low Power Atmospheric Plasma Jet Torch for Optical Fabrication