Abstract:This paper investigates the internal flow characteristics of an aggressive S-shaped air bleeding manifold under typical working condition with the throttle cone opening degree of 15% and the inlet Mach number of 0.34 by experimental and numerical simulation methods. Based on the experimental results of total pressure recovery coefficient, the realizable kε model was selected as a suitable turbulence model for the air bleeding manifold numerical simulation by analyzing the numerical results of different turbulence models. The numerical simulation results show that the flow separation occurs at the upper wall and lower wall near the first bend, which also leads to the vortex pair and causes the nonuniformity of the flow field in the exit. The curvature of the end walls and the cross-sectional area variation of air bleeding manifold have greatly influence on the flow structure. The severe deflectionon the lower wall of the first bend is the main factor causing the flow separation and total pressure loss. The mass-averaged total pressure recovery coefficient in exit is 0.9818, and the synthesis distortion index DC(60) in the exit is 0.1334.. INTRODUCTION Air bleeding manifold is an important component in the active clearance control system of high-pressure turbine. The study of the internal characteristic and the loss mechanism will provide theoretical basis for optimal design of the air bleeding manifold. In this paper, the air bleeding manifold is an aggressive S-shaped duct with variable geometric crosssection. The study on flow characteristics of S-shaped duct in aero-engine is focused on compressor and turbine intermediate duct [1-3], inlet [4-5] and nozzle [6]. It is very famous that AIDA-Aggressive Intermediate Duct Aerodynamics project within the 6th framework program funded by the European Commission two projects dealing exclusively or partly with the topic of intermediate ducts. The outcomes of the AIDA project gives turbine and compressor engineers access to a whole new class of validated “aggressive” duct designs and design tools that will allow a much better optimization of the whole compression and turbine system [7] . The pressure distribution in an S-shaped diffuser depends not only on the area change such as in straight-walled channels, but also upon the curvature of the end walls and hence of the streamlines. S-shaped diffuser has a major effect on the boundary layer behavior at the end walls, which is most critical due to the strongest adverse pressure gradients right after strong wall curvatures [7]. This feature makes the numerical simulation and testing of an aggressive S-shaped diffuser difficult. Wellborn et al. [8] observed the intense mixture of the boundary layer and the core flow in the wind tunnel experiment with the inlet Mach number of 0.6. The counter-rotating vortices convected low momentum fluid of the boundary layer toward the center of the duct, and a large region of streamwise flow separation occurred within the duct. A large number of experimental studies have been carried out on the flow characteristics of S-shaped duct [9-13]. About the numerical simulation study, many researchers have done lots of work to find more accurate turbulence models for numerical simulation [14-18]. Waston et al. [18] calculated the NASA 30/30 geometric model using RANS (S-A, k-ε and SST k-ω model) and zonal large eddy simulation (RANS/LES) approaches. It was found that LES could more reliably predict large degrees of separation, but the mesh requirements and consequent cost render the technique prohibitively expensive for the near future, certainly unacceptably so for routine calculations as part of an ongoing design process. Asghar et al.[19-20] explored the flow characteristics of a baseline Sshaped diffuser using experiment and numerical simulation methods. They concluded that the presence of streamwise and circumferential pressure gradients led to the 3-D flow and the flow distortion in the exit. In addition, different geometry parameters of the S-shaped diffuser would have greatly influence on the flow characteristics. In this paper, the internal flow characteristics of an aggressive S-shaped air bleeding manifold of high-pressure turbine with active clearance

Flow characteristics and separation control in a transitional twin air-intake

SHOCK INDUCED SEPARATING FLOWS IN SCRAMJET INTAKES

Scramjet Intake Aerodynamic Studies Using Sharp Interface Immersed Boundary Method

Flow and heat transfer studies of multijet impingement cooling for different configurations: A review

Separation flow control and engineering application of synthetic jets in compressor

Distortion Control in Intakes Subject to Strong Crosswinds Using Steady Vortex Generator Jets

Fluid Flow Characteristics of a Co-Flow Fluidic Slot Jet Thrust Augmentation Propulsion System

Control of flow separation over a circular cylinder using synthetic jet

Flow Control of Annular Compressor Cascade by Synthetic Jets

Design optimization and off-design performance analysis of axisymmetric scramjet intakes for ascent flight

Numerical Analysis Of Active Flow Control Around Airfoil By Synthetic Jet Technology In Low Reynolds Number

Unsteady Flow Control Mechanism of Synthetic Jet on a Low Pressure Turbine Blade

Flow characteristics in the air bleeding manifold

Performance Improvement of Low Pressure Turbine Blade by Using Synthetic Jets

High-resolution turbofan intake flow characterization by automated stereoscopic-PIV in an industrial wind tunnel environment

A Survey on Control Techniques to Augment Compressible Jet Mixing

Experimental simulation methodology and spatial transition of complex distortion fields in a S-shaped inlet

The study of cascading effect in the integration of intake with gas turbine engine bay in subsonic cruise vehicle

Numerical investigation on implication of innovative hydrogen strut injector on performance and combustion characteristics in a scramjet combustor

Effect of perforated wall in controlling the separation due to SWBLI at Mach no. 5 to 9

Numerical Investigation of Inlet Distortion for Different Rear Mounted Engine Installations at Taking-Off Conditions