Abstract:Because of the advantages of high theoretical capacity, low cost, and environmental friendliness, lithium–sulfur (Li–S) batteries have attracted wide attention as promising energy storage system for electric vehicles and smart power grids. However, their commercialization is still greatly restricted by their poor cycle stability, resulting from the severe shuttling of soluble lithium polysulfides (LiPSs) during cycling. Herein, we designed a polymer/rGO (/rGO) blocking layer on a commercial PP separator. Such a blocking layer can strongly fix LiPSs by the electrostatic attraction effect between the cationic polymer backbones and the polysulfide anions. As a result, a Li–S battery equipped with a /rGO-functionalized separator showed much improved cycling stability with a capacity fading rate as low as 0.06% per cycle during 700 cycles at 1 C. Especially, high areal capacity of 6.3 mAh cm–2 was also achieved with a high sulfur loading of 8.5 mg cm–2 after 50 cycles. This work highly emphasizes that the electrostatic attraction mechanism between cationic polymers and polysulfides can effectively restrain the polysulfide shuttling and thus significantly improve the electrochemical performance of Li–S batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00281?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00281</a>.SEM image of initial CNTs, TEM image and XPS survey spectrum of , SEM images and XRD patterns of GO and rGO, Raman and N2 adsorption/desorption isotherm of /rGO, Nyquist plots of /rGO separator and PP separator, CV curves and charge–discharge curves of Li–S batteries with PP separators, long-term cycling performance of the Li–S batteries with /rGO separator at 0.5 and 2 C, CV curves of Li–S batteries with /rGO separator and PP separator for the first cycle at 0.1 mV s–1, charge–discharge curves of Li–S batteries with high sulfur loading using /rGO separator and PP separator (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00281/suppl_file/ae1c00281_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Manufacturing N,O-carboxymethyl chitosan-reduced graphene oxide under freeze-dying for performance improvement of Li-S battery

Enhanced cycle performance of Li/S battery with the reduced graphene oxide/activated carbon functional interlayer

Enhanced Performance of Lithium Sulfur Battery with A Reduced Graphene Oxide Coating Separator

Energy-Saving Synthesis of Functional CoS2/rGO Interlayer With Enhanced Conversion Kinetics for High-Performance Lithium-Sulfur Batteries

Inhibiting the Shuttle Effect of Li–S Battery with a Graphene Oxide Coating Separator: Performance Improvement and Mechanism Study

Synthesis of porous-carbon@reduced graphene oxide with superior electrochemical behaviors for lithium-sulfur batteries

Investigation on Fabrication of Reduced Graphene Oxide-Sulfur Composite Cathodes for Li-S Battery via Hydrothermal and Thermal Reduction Methods

Porous 3D nitrogen-doped rGO/Co-Ni-S composite modified separator for high-capacity and stable lithium-sulfur batteries

Fabricating Ultrathin ZrB2/Graphene Oxide/carboxymethocel Layer Onto Cathode As Effective Polysulfide Shuttling Barrier for Li–S Battery

Sandwich-like NOCC@S8/rGO composite as cathode for high energy lithium-sulfur batteries

A multifunctional separator modified with cobalt and nitrogen co-doped porous carbon nanofibers for Li–S batteries

Electrocatalytic polysulfide transformation for suppressing the shuttle effect of Li-S batteries

Boosting Polysulfide Confinement and Redox Kinetics Via ZnSe/NC@rGO As Separator Modifier for High-Performance Lithium-Sulfur Batteries

Effective Suppression of the Polysulfide Shuttle Effect in Lithium–Sulfur Batteries by Implementing rGO–PEDOT:PSS-Coated Separators via Air-Controlled Electrospray

Reduced porous carbon/N-doped graphene nanocomposites for accelerated conversion and effective immobilization of lithium polysulfides in lithium-sulfur batteries

Slurryless Li2S/reduced graphene oxide cathode paper for high-performance lithium sulfur battery.

Light-weight functional layer on a separator as a polysulfide immobilizer to enhance cycling stability for lithium–sulfur batteries

Layer-by-Layer Assembly of CeO2-x@C-rGO Nanocomposites and CNTs As a Multifunctional Separator Coating for Highly Stable Lithium-Sulfur Batteries

In-situ lithiation synthesis of nano-sized lithium sulfide/graphene aerogel with covalent bond interaction for inhibiting the polysulfides shuttle of Li-S batteries

Rational In-Situ Construction of Three-Dimensional Reduced Graphene Oxide Supported Li2s/C Composite As Enhanced Cathode for Rechargeable Lithium-Sulfur Batteries

Cationic-Polymer-Functionalized Separator As a High-Efficiency Polysulfide Shuttle Barrier for Long-Life Li–S Battery