Abstract:Because of the advantages of high theoretical capacity, low cost, and environmental friendliness, lithium–sulfur (Li–S) batteries have attracted wide attention as promising energy storage system for electric vehicles and smart power grids. However, their commercialization is still greatly restricted by their poor cycle stability, resulting from the severe shuttling of soluble lithium polysulfides (LiPSs) during cycling. Herein, we designed a polymer/rGO (/rGO) blocking layer on a commercial PP separator. Such a blocking layer can strongly fix LiPSs by the electrostatic attraction effect between the cationic polymer backbones and the polysulfide anions. As a result, a Li–S battery equipped with a /rGO-functionalized separator showed much improved cycling stability with a capacity fading rate as low as 0.06% per cycle during 700 cycles at 1 C. Especially, high areal capacity of 6.3 mAh cm–2 was also achieved with a high sulfur loading of 8.5 mg cm–2 after 50 cycles. This work highly emphasizes that the electrostatic attraction mechanism between cationic polymers and polysulfides can effectively restrain the polysulfide shuttling and thus significantly improve the electrochemical performance of Li–S batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00281?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00281</a>.SEM image of initial CNTs, TEM image and XPS survey spectrum of , SEM images and XRD patterns of GO and rGO, Raman and N2 adsorption/desorption isotherm of /rGO, Nyquist plots of /rGO separator and PP separator, CV curves and charge–discharge curves of Li–S batteries with PP separators, long-term cycling performance of the Li–S batteries with /rGO separator at 0.5 and 2 C, CV curves of Li–S batteries with /rGO separator and PP separator for the first cycle at 0.1 mV s–1, charge–discharge curves of Li–S batteries with high sulfur loading using /rGO separator and PP separator (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00281/suppl_file/ae1c00281_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Energy-Saving Synthesis of Functional CoS2/rGO Interlayer With Enhanced Conversion Kinetics for High-Performance Lithium-Sulfur Batteries

Elaborate interface design of CoS2/Fe7S8/NG heterojunctions modified on a polypropylene separator for efficient lithium-sulfur batteries

Ultrathin Cobalt Phthalocyanine@Graphene Oxide Layer-Modified Separator for Stable Lithium–Sulfur Batteries

Ultrafine Co-Species Interspersed g-C3N4 Nanosheets and Graphene as an Efficient Polysulfide Barrier to Enable High Performance Li-S Batteries

3D CoS2/rGO Aerogel As Trapping-Catalyst Sulfur Host to Promote Polysulfide Conversion for Stable Li-S Batteries

A multifunctional separator modified with cobalt and nitrogen co-doped porous carbon nanofibers for Li–S batteries

Sulfonic Groups Originated Dual-Functional Interlayer for High Performance Lithium-Sulfur Battery

Regulating Polysulfide Intermediates by Ultrathin Co-Bi Nanosheet Electrocatalyst in Lithium−sulfur Batteries

Decorating CoSe 2 Hollow Nanospheres on Reduced Graphene Oxide As Advanced Sulfur Host Material for Performance Enhanced Lithium-Sulfur Batteries

Layer-by-Layer Assembly of CeO2-x@C-rGO Nanocomposites and CNTs As a Multifunctional Separator Coating for Highly Stable Lithium-Sulfur Batteries

CoN//Co 9 S 8 co-embedded in reduced graphene oxide as catalyst for catalytic conversion of polysulfides

2D Cu 2− x Se@graphene multifunctional interlayer boosting polysulfide rapid conversion and uniform Li 2 S nucleation for high performance Li–S batteries

Porous 3D nitrogen-doped rGO/Co-Ni-S composite modified separator for high-capacity and stable lithium-sulfur batteries

A Two-Dimensional Heterostructured Covalent Organic Framework/Graphene Composite for Stabilizing Lithium–Sulfur Batteries

Novel 2D bifunctional layered rare-earth hydroxides@GO catalyst as a functional interlayer for improved liquid-solid conversion of polysulfides in lithium-sulfur batteries

Cationic-Polymer-Functionalized Separator As a High-Efficiency Polysulfide Shuttle Barrier for Long-Life Li–S Battery

Boosting Polysulfide Confinement and Redox Kinetics Via ZnSe/NC@rGO As Separator Modifier for High-Performance Lithium-Sulfur Batteries

Regulating the Kinetic Behaviors of Polysulfides by Designing an Au-COF Interface in Lithium-Sulfur Batteries

CoP@C with chemisorption-catalysis effect toward lithium polysulfides as multifunctional interlayer for high-performance lithium-sulfur batteries

Functional Separator Modified with Reduced Graphene Oxide and Fe3S4 for High-Performance Lithium–Sulfur Batteries

Functional Separator Modified with Reduced Graphene Oxide and Fe 3 S 4 for High-Performance Lithium–Sulfur Batteries