Abstract:This study focuses on the valorization of the Agave sisalana plant from the southern region of Morocco. The research objective is to enhance the sisal fiber extraction process and examine the impact of various chemical treatments on their mechanical properties, crucial for composite reinforcement. The sisal fibers were mechanically extracted from the leaves, initially washed and calendered under a pressure of 5KN, then mechanically scraped to separate the fibers from the pulp. Subsequently, they were combed and washed three times to remove impurities and then dried at 105 °C for 24 h. To effectively remove impurities, treatment with NaOH was carried out by adjusting three variables: NaOH concentration (0.5%, 1%, and 1.5%), temperature (60, 70, and 80 °C), and duration (30, 60, and 90 min). The optimal conditions for NaOH treatment were determined using a response surface methodology (RSM) approach. The highest results were obtained with samples treated with 0.5% NaOH at a temperature of 65 °C for 40 min. Sisal fibers with the highest tensile properties were treated with potassium permanganate (KMnO 4 ) and the other sodium chlorite (NaClO 2 ). The effects of these treatments on physical and chemical properties were subsequently analyzed through various methods, including scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis, mechanical tests, and water resistance assessment. The results indicate that Moroccan sisal fiber has a low density of 1.21 ± 0.0347 g/cm 3 and a high cellulose content of 63.33%. The microstructural observations through scanning electron microscopy (SEM) depicted a noticeable morphological change in both untreated and treated sisal fibers, presenting a roughened surface. The FTIR analysis revealed a reduction in phenolic and secondary alcohol functional groups, as well as a decrease in hydrogen bonding resulting from the treatment of sisal fiber. According to the results, the most effective treatment for increasing the tensile strength of sisal fibers was achieved with 0.5% NaOH and 0.09% KMnO 4 , reaching a maximum value of 535 ± 8 MPa. This same treatment also led to a reduction in moisture absorption and water absorption of raw sisal fiber by 61 and 56%, respectively. Pull-out test results indicate that treating Moroccan sisal fibers with KMnO 4 and NaClO 2 can increase the pull-out load from 26 N to 98 ± 1.8 N and 87 ± 1.5 N, respectively. In conclusion, the findings of this study emphasize the significant promise of sisal fiber as a reinforcement material for composites. With its demonstrated capabilities, sisal emerges as a viable option for sustainable and environmentally friendly reinforcement across various applications.

Effect of Various Chemical Treatments on Physical, Mechanical, Thermal and Morphological Properties of Calotropis Gigantea Bast Fiber

Effect of Different Chemical Treatments on the Dispersion Properties of Carbon Fiber and Paper Properties

Influence of chemical treatment on tensile strength, water absorption, surface morphology, and thermal analysis of areca sheath fibers

Characterization of alkali-treated cellulosic fibers derived from Calamus tenuis canes as a potential reinforcement for polymer composites

Study on Physical, Mechanical, Morphological, and Crystallographic Properties of Chemically Treated Sisal Fibers

The influence of fiber content and length on mechanical and water absorption properties of Calotropis Gigantea fiber reinforced epoxy composites

Effect of Surface Modification of Himalayan Nettle Fiber and Characterization of the Morphology, Physical and Mechanical Properties

Investigation on the mechanical, water absorption, and tribological performance of calotropis gigantea and abaca fiber reinforced epoxy composites

Investigation of mechanical, thermal, and chemical properties of raw and NaOH-treated bagasse/halfa grass/coir fiber

Effect of alkali treatment on new lignocellulosic fibres from the stem of the Aster squamatus plant

Investigating the Mechanical, Thermal, and Crystalline Properties of Raw and Potassium Hydroxide Treated Butea Parviflora Fibers for Green Polymer Composites

Influence of optimal alkali treated Areca catechu L. peduncle fiber for light weight polymer composites applications

Nano-clay treatment of jute fiber for reinforcement in polymer composites: Mechanical, morphological, and thermo-kinetic analysis

Impact of Surface Treatment on the Strengthening of Geopolymer Composites Reinforced with Short Sisal Fibers

The effect of eco-friendly chemical treatment on sisal fiber and its epoxy composites: thermal, mechanical, tribological and morphological properties

Chemical Treatments for Modification of the Surface Morphology of Coir Fiber: A Review

Effect of chemical treatments of fibre surface on mechanical properties and wear rate of Beerakaya (Luffa acutangula) reinforced epoxy polymer composites

Effect of chemical modification of fiber surface on natural fiber composites: A review

Characteristics of surface modified sugarcane bagasse cellulose: application of esterification and oxidation reactions

Effect of Potassium Permanganate treatment on physico-Chemical and mechanical properties of extracted Pine Needle Fiber

Extraction and chemical treatments of Moroccan sisal fiber for composite applications