Abstract:The numerical simulation problem of the frictional contact interaction of the flat sliding layer periodicity cell of the spherical bearing is performed. The mathematical formulation of contact problems with a previously unknown contact area and all types of contact states (adhesion, sliding, no contact) is done. Three options for the sliding layer thickness of 4, 6 and 8 mm are considered. The deformation of the thin flat sliding layer of the spherical bearing is made on the example of an antifriction layer of modified PTFE. The deformation theory of elastoplasticity for the active loading case is chosen as the antifriction polymer behavior model. The thermomechanical and friction properties of the modified PTFE were obtained experimentally by a scientific group of Alfa-Tech LLC and IMSS of the Ural Branch of the Russian Academy of Sciences. The experiment to determine the frictional properties of the material was performed to a pressure level of 54 MPa. The analysis of the friction coefficient dependence on the level of pressure acting on the stamp is performed: approximating functions and for contact with \documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \upmu\left( P \right) = 0.005 + {{0.111} \mathord{\left/ {\vphantom {{0.111} P}} \right. \kern-0pt} P} + {{0.623} \mathord{\left/ {\vphantom {{0.623} {P^{2} }}} \right. \kern-0pt} {P^{2} }} - {{3.57} \mathord{\left/ {\vphantom {{3.57} {P^{3} }}} \right. \kern-0pt} {P^{3} }} + {{3.335} \mathord{\left/ {\vphantom {{3.335} {P^{4} }}} \right. \kern-0pt} {P^{4} }} $$\end{document} and \documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$ \upmu\left( P \right) = - 0.002 + {{1.55} \mathord{\left/ {\vphantom {{1.55} P}} \right. \kern-0pt} P} - {{17.166} \mathord{\left/ {\vphantom {{17.166} {P^{2} }}} \right. \kern-0pt} {P^{2} }} + {{64.979} \mathord{\left/ {\vphantom {{64.979} {P^{3} }}} \right. \kern-0pt} {P^{3} }} - {{55.745} \mathord{\left/ {\vphantom {{55.745} {P^{4} }}} \right. \kern-0pt} {P^{4} }} $$\end{document} without lubricant on the mating surfaces are selected. The friction coefficient for a pressure level of more than 54 MPa is calculated from the obtained functions with an error of less than 1%. Simulation of the spherical bearing sliding layer deformation behavior is made taking into account the physicomechanical and friction properties of the polymer material using the example of a periodicity cell made of the modified PTFE with a hole for lubrication. Distribution fields of stress intensity and plastic strain intensity, as well as integral stiffness were obtained and analyzed. The relations of the maximum and minimum integral parameters values of the stress-strain state on the pressure level are established as part of the analysis. The influence of frictional properties and layer thickness on the contact zone parameters is considered. It was established that the 8 mm thickness layer enjoy a more favorable deformation behavior case than the other two variants of the layer thickness. The frictional properties have a slight effect on the stress-strain state parameters of the periodicity cell, their influence significantly on the pattern of the contact states zones distribution and contact tangential stress. It is established that the level of contact tangential stress when taking into account lubricant approximately is on lower 3 times than with contact without lubrication.

Regarding the Question of Calculation of Contact Pressure in Metal-Polymer Plain Bearings during Wear

Triboanalysis of Antifrictional Materials Based on Polyamides for Metal-Polymer Sliding Bearings

ANALYTICAL STUDY OF DURABILITY AND CONTACT CHARACTERISTICS OF METAL-POLYMER COMPOSITE SLIDING BEARINGS FOR MEANS OF TRANSPORT

Method of calculation of tribotechnical characteristics of the metal-polymer gear, reinforced with glass fiber, taking into account the correction of tooth

Estimation of tribotechnical parameters of composite polymer with metal filler

Comparative Evaluation of Tribological Effectiveness of Carbon- and Glass-Filled Polyamide Composites Using Submicromechanical Diagnostics of Surface Layers before and after Wear Tests during Dry Sliding Friction

Wear performance of bulk oriented nanocomposites UHMWPE/FMWCNT and metal-polymer composite sliding bearings

Experimental Analysis and Wear Prediction Model for Unfilled Polymer–Polymer Sliding Contacts

Deformation Behavior Numerical Analysis of the Flat Sliding Layer of the Spherical Bearing with the Lubrication Hole

Resource testing of modified plain bearings for the aviation industry

Comparison of Friction and Wear Performances of Pure Poly-ether-ether-ketone Polymer and Carbon Fiber Reinforced Poly-ether-ether-ketone Polymer Composite for Bushing and Bearing Applications

Application of metal-polymer plain bearings for heavily loaded friction angles

Application of Submicromechanical Diagnostics for Characterization of Glass-Filled Polyamide Composites

Wear resistance of nanostructured metal-polymer self-lubricating powder composites

Polymer composites based on aromatic polyamide and fillers of spherical and layered structure for friction units of high-performance equipment

On the ability of polymers to self-lubrication in metal – polymer friction pairs

Methods for increasing the wear resistance of heavy loaded metal-polymer tribosystems

FEATURES OF MANUFACTURING AND CALCULATION OF GEARS FOR NEW APPLICATIONS (REVIEW)

Prediction of wear of short glass fiber reinforced polyamide 66 composite sprocket

Coefficient of mutual overlap in metal-polymer tribosystems

Experimental simulation of the friction, temperature, and wear distributions for polyamide–steel gear contact using twin-disc setup