Abstract:The structure, morphology, and mechanical properties of two compression-molded grades of ultrahigh-molecular-weight polyethylene (UHMWPE) and, for comparison, one conventional linear polyethylene (HDPE) were studied. Compression molding resulted in some preferred orientation of lamellae in the compression direction in UHMWPE samples, while no preferred orientation in HDPE. The mean crystal thickness estimated from the size distribution agrees better with those obtained from small-angle X-ray scattering (SAXS) and mechanical yield data than the thickness determined from the melting peak temperature. Microscopic examination of microtomed and etched UHMWPE samples showed that the lamellae are in the form of platelets with the width and length in the range of 300-700 nm. The lamellae radiate from primary nuclei forming small embryonal spherulites; their radial growth ends at 0.3-0.7 μm from the center. There is no evidence of branching and secondary nucleation from those primary lamellae. Because the lamellae are radially ordered, there is no parallel stacking of lamellae. Samples were subjected to deformation by plane-strain compression at a constant true strain rate. In axial UHMWPE samples, where lamellae were preferentially oriented along the loading direction, the second yield was clearly observed. The second yield was found to be related to the deformation instability leading to kinking of lamellae oriented initially along the loading direction. Kinking was clearly shown by SAXS and microscopic observation of microtomed and etched samples. No cooperativity of kinking was observed because the lamellae are arranged in small spherulites and not parallel in stacks. The stress-strain curves were fitted with model curves assuming crystal plasticity and network elasticity in the amorphous component. The effective density of the molecular network within the amorphous phase depended on the molecular weight of UHMWPE.

Thermal actuation shape memory of ultra-high-molecular-weight polyethylene (UHMWPE) with molecular orientation

Ultra-high Stretchability and Shape Fixation Rate Shape Memory Polyurethanes Based on Cyclic Polytetrahydrofuran Molecular Rings

One-way Shape Memory Behavior of Thermoplastic Polyolefin Elastomers

Omnidirectional Shape Memory Effect Via Lyophilization of Peg Hydrogels

Effect of PEW and CS on the Thermal, Mechanical, and Shape Memory Properties of UHMWPE

Heating‐Responsive Shape‐Memory Effect in Thermoplastic Polyurethanes with Low Melt‐Flow Index

Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene

Reversed thermal stability between stress-induced melting and recrystallized crystallites and original inclined ones in moderately stretched ultra high molecular weight polyethylene and high density polyethylene

The Shape Memory Effect of Crosslinked Ultra-High-molecular-weight Polyethylene Prepared by Silane-Induced Crosslinking Method

Achieving high thermal conductivity and mechanical reinforcement in ultrahigh molecular weight polyethylene bulk material

Deformation of Ultrahigh Molecular Weight Polyethylene Precursor Fiber: Crystal Slip with or Without Melting

Enhancing Chain Mobility of Ultrahigh Molecular Weight Polyethylene by Regulating Residence Time under a Consecutive Elongational Flow for Improved Processability

Constructing highly oriented and condensed shish-kebab crystalline structure of HDPE/UHMWPE blends via intense stretching process:Achieving high mechanical properties and in-plane thermal conductivity

Shish-kebab Structure Evolution of HDPE/UHMWPE During Hot Drawing

Melting Behavior and Morphology of Freeze-Dried Ultra-High Molar Mass Polyethylene

Melt Processing and Structural Manipulation of Highly Linear Disentangled Ultrahigh Molecular Weight Polyethylene

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Tunable shape memory effect and omnidirectional shape change of polyetheretherketone

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Photo-thermal actuation of ultra-drawn high-density polyethylene

The influence of UHMWPE with varying morphologies on the non-isothermal crystallization kinetics of HDPE