Abstract:Traditional cement-based grouting materials have good reinforcement and anti-seepage effects on the surrounding rock under normal conditions, but the grouting effect is not ideal due to problems such as a long setting time, a low stone ratio, and poor crack resistance under high water pressure and in a dynamic water environment. In this study, we aimed to improve the physical properties, chemical properties, and microstructure of a cement-based slurry by forming a hydrogel through its chemical crosslinking with polyvinyl alcohol and boric acid as modifiers for the purpose of improving the permeability resistance of the surrounding rock grouting under high-water-pressure conditions, which can expand the function of traditional building materials. The grouting effect of the modified cementitious material on the surrounding rock was analyzed through indoor tests, the SEM testing of the performance of the modified slurry, the numerical calculation of the seepage field, and the application of the modified slurry in combination with the actual project to verify the water-plugging effect. The research findings demonstrate that (1) the additives boric acid and PVA can significantly speed up the slurry gel time, and the gel time can be controlled within 2–20 min to meet the specification requirements. (2) At a velocity of moving water > 1 m/s, the retention of the solidified modified slurry stone body reaches more than 80%. According to the SEM analysis, the structure of the solidified modified slurry stone body is dense and has good impermeability. (3) According to the numerical calculation analysis, the modified slurry can effectively change the seepage field of the surrounding rock and improve its seepage resistance. The water pressure outside the lining is reduced by 47%, 31%, and 22%, respectively, compared with no slurry, the pure cement slurry, and cement–water-glass grouting, and the indoor test and numerical simulation conclusions are consistent.

The Technique of Single-Component Synchronous Grouting Allocation to Resist Floating in High Pressure Water-Rich Formation

Sedimentation-affected Engineering Performances and Microstructures of a Hybrid Portland- Sulfate Aluminate Cement Grout Cast in Long Tubes

Numerical Investigation of Grout Diffusion Accounting for the Dynamic Pressure Boundary Condition and Spatiotemporal Variation in Slurry Viscosity

Study on the Floating of Large Diameter Underwater Shield Tunnel Caused by Synchronous Grouting

High-Fluidization, Early Strength Cement Grouting Material Enhanced by Nano-SiO2: Formula and Mechanisms

Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

A novel water-swelling grouting material formulation and its performance for water rushing in karst strata

Rheology and Yield Stress Evolution of Highly Flowable Cementitious Grouting Materials: Mechanisms and Modeling

Investigation on basic properties and microscopic mechanisms of polyacrylate latex modified cement grouting material for water blocking and reinforcement

Application of CO 2 -foamed lightweight grout with early strength and low density as a low-carbon material in shield synchronous grouting

Research on the connection performance and micro-hydration mechanism of super-performance grouting material for prefabricated component connections

Experimental Investigation of Synchronous Grouting Material Prepared with Different Mineral Admixtures

Non-Dispersive Anti-Washout Grout Design Based on Geotechnical Experimentation for Application in Subsidence-Prone Underwater Karstic Formations

Development and application of novel microfine cement-based grout

Experimental Study on Fresh State Properties of Single-Liquid Semi-Inert Synchronous Grouting for Shield Tunnels in Water-Rich Sand Strata

Experimental Study on Performance of Modified Cement-Based Building Materials under High-Water-Pressure Surrounding Rock Environment

Advanced Grouting Model and Influencing Factors Analysis of Tunnels with High Stress and Broken Surrounding Rock

Multi-Response Optimization of High-Performance Low-pH Grouting Materials by Using Taguchi-Based Grey Relational Analysis

The Effect of Incorporating Ultra-Fine Spherical Particles on Rheology and Engineering Properties of Commercial Ultra-High-Performance Grout

Strengthening effect of sulphoaluminate cementitious grouting material for water-bearing broken rocky stratum

Seepage behavior and mechanical properties of two kinds of polyurethane/water glass in combined grouting experiment