Abstract:As the first material ever used in a solid-state solar cell, selenium (Se) has outstanding merits of light absorption, carrier mobility, intrinsic environmental stability, and straightforward film preparation, making it an attractive light-absorbing semiconductor for photovoltaic applications. However, the exploration of selenium for photoelectrochemical (PEC) cells remains vastly unreported. Here, we successfully enable selenium as an absorber in the photocathode for solar hydrogen production. A rapid thermal annealing process is adopted to prepare a tetragonal Se film with a preferred [100] orientation. Using a thin layer of TiO2 buffer and platinum decoration, a photocurrent density up to −7.2 mA/cm2 is achieved over the optimal Se/TiO2/Pt photocathode at 0 VRHE under simulated one sun illumination. The roles of surface state passivation by TiO2 and cocatalyst decoration by Pt in charge separation and transfer were thoroughly investigated by capacitance–voltage profiling, photoassisted Kelvin probe force microscopy, photoelectrochemical impedance spectroscopy, and also transient photovoltage decay. Our work provides Se as a promising candidate for solar hydrogen production and also highlights the effectiveness of surface state passivation and cocatalyst decoration in the fabrication of efficient PEC devices.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.1c03066?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.1c03066</a>.Additional photoelectrocatalytic data, XRD patterns, and MS plots; details for calculation of the texture coefficients of the orientated t-Se film and energy band position; fitted resistances of the EIS results (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.1c03066/suppl_file/sc1c03066_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Melt- and air-processed selenium thin-film solar cells

Magnetron Sputtered Sb2Se3-based Thin Films Towards High Performance Quasi-Homojunction Thin Film Solar Cells

Enabling Solar Hydrogen Production over Selenium: Surface State Passivation and Cocatalyst Decoration

Standing 1D Chains Enable Efficient Wide‐Bandgap Selenium Solar Cells

Solution-Processed Air-Stable Mesoscopic Selenium Solar Cells

GeSe Thin-Film Solar Cells Fabricated by Self-Regulated Rapid Thermal Sublimation

Lanthanide‐Like Contraction Enables the Fabrication of High‐Purity Selenium Films for Efficient Indoor Photovoltaics

Rapid Thermal Annealing Process for Se Thin-Film Solar Cells.

Single-source Thermal Evaporation Converts Anion Controllable Sb 2 (s,se) 3 Film for Fabricating High-Efficiency Solar Cell

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

Hydrothermal deposition of antimony selenosulfide thin films enables solar cells with 10% efficiency

Laser-Annealing and Solid-Phase Epitaxy of Selenium Thin-Film Solar Cells

Direct Hydrothermal Deposition of Antimony Triselenide Films for Efficient Planar Heterojunction Solar Cells

Sputtered and Selenized Sb2Se3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 Mv

Sequential Coevaporation and Deposition of Antimony Selenosulfide Thin Film for Efficient Solar Cells

Pulsed laser deposition of antimony selenosulfide thin film for efficient solar cells

Sb2Se3 Thin-Film Photovoltaics Using Aqueous Solution Sprayed SnO2 As the Buffer Layer

Highly Efficient and Stable Planar Heterojunction Solar Cell Based on Sputtered and Post-Selenized Sb 2 Se 3 Thin Film

Se-Elemental Concentration Gradient Regulation for Efficient Sb2(S,Se)3 Solar Cells With High Open-Circuit Voltages

Low-cost and high-performance selenium indoor photovoltaics

Enhanced performance of GeSe thin-film solar cells via bifacial charge transport materials design