Abstract:With the advancement of laser powder bed fusion (LPBF) for aluminum alloys, developing novel lightweight Al–Li alloy systems present enormous potential for aerospace applications. Conventional Al–Mg–Li alloys exhibit low densities but suffer from poor strength due to the lack of inherent strengthening phases. In the present work, a novel lightweight Al–Mg–Li–Ag-Sc-Zr alloy was developed for LPBF after optimizing the processing parameters. The as-built alloy featured a bimodal microstructure consisting of fine equiaxed grains and columnar grains. The submicron primary Al 3 (Sc, Zr) phases with a cubic L 1 2 structure served as inoculants for grain refinement and exhibited good coherency with the α-Al matrix. Besides, submicron spherical quasicrystalline T-Mg 32 (Al, Ag) 49 phases of and nanometer rod-shaped S 1 –Al 2 MgLi phases were scattered inside the grains. These results produced a yield strength (σ y ) of 286 ± 8 MPa, ultimate tensile strength (σ UTS ) of 406 ± 3 MPa, and elongation at fracture (ε f ) of 12.5 ± 0.3%. The direct aging at 325 °C for 12 h led to an increase in hardness to a peak value of 170 HV. The secondary phases at the grain boundaries were breached and a large amount of submicron T and S 1 phases within the grains were prominently increased. Besides, spherical Al 3 (Sc, Zr, Li) and tiny δ′-Al 3 Li precipitates were observed in the α-Al matrix. A considerably enhanced σ y of 375 ± 12 MPa and σ UTS of 469 ± 4 MPa were achieved mainly due to the particle strengthening but decreased ε f to 5.8 ± 0.2%. The alloys in both states exhibited a moderate work-hardening capability. The feasibility of LPBF for lightweight Al–Li alloy was successfully established but required further optimization of the alloy composition.

Research Progress of Low Density and High Stiffness of Be-Al Alloy Fabricated by Investment Casting

High ductility of Be–Al alloy fabricated by investment casting

Development and Research Status of Investment Casting TiAl-Based Alloys

Achieving ultra-high strength in Be/Al composites by self-exhaust pressure infiltration and hot extrusion process

Role of alloying and heat treatment on microstructure and mechanical properties of cast Al-Li alloys: A review

Strengthening-Toughening of High-Strength Al-Zn Cast Aluminum Alloys: Research Progress and Prospects

Low‐cycle Fatigue Behavior of a Newly Developed Cast Aluminum Alloy for Automotive Applications

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

Microstructures and mechanical properties of a cast Al–Cu–Li alloy during heat treatment procedure

An Investigation into Aluminum–aluminum Bimetal Fabrication by Squeeze Casting

Development and applications of aluminum alloys for aerospace industry

A New High-Strength and Corrosion-Resistant Al–Si Based Casting Alloy

Recent progress of aluminum alloys and aluminum matrix composites produced via laser powder bed fusion: a review

Research Progress in Aluminum Alloy Additive Manufacturing

Research Status and Prospective Properties of the Al-Zn-Mg-Cu Series Aluminum Alloys

Fabrication and properties of in situ (Al3Zr + Al2O3)p/A356 composites cast by permanent mould and squeeze casting

Research progress on dimensional accuracy control technologies of complex thin-walled superalloy investment castings for aero-engines

Research Progress of New Generation of Aluminum‐Lithium Alloys Alloying

Numerical Simulation and Process Optimization of Vacuum Investment Casting for Be–Al Alloys

Synthesis of an (Al3BC + Al2O3)/Al composite with high stiffness and attractive high-temperature tensile properties

Data-Driven Design of Cast Nickel-Based Superalloy and Precision Forming of Complex Castings