Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

Microstructural Characteristics-based Mechanical Behavior of Aerospace Al-Cu Alloys

Micromechanical Simulation on Strength and Ductility of Two Kinds of Al-based Nanostructural Materials

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Research Progress on the Microstructure Evolution Mechanisms of Al-Mg Alloys by Severe Plastic Deformation

Microstructure Modelling and Simulation of Shaped Casting with Mca Method

Microstructure based analysis and predictive modeling of cast Al7Si1.5Cu0.4Mg alloy mechanical properties

The Influence of Casting Microvoids on the Constitutive Behavior of As-Quenched Al-Cu-Mn Alloy

Casting defects and microstructure distribution characteristics of aluminum alloy cylinder head with complex structure

Application of Microstructure Simulation by Modified Ca Method to Al Alloy Casting Production

Microstructures and mechanical properties of a cast Al–Cu–Li alloy during heat treatment procedure

Role of alloying and heat treatment on microstructure and mechanical properties of cast Al-Li alloys: A review

Uncovering the effects of local pressure and cooling rates on porosity formation in AA2060 Al-Li Alloy

Microstructure evolution, constitutive modeling and forming simulation of AA6063 aluminum alloy in hot deformation

Modeling the Precipitation Kinetics and Tensile Properties in Al-7si-Mg Cast Aluminum Alloys

Microstructure evolution and mechanical responses of Al–Zn–Mg–Cu alloys during hot deformation process

Modeling of microporosity evolution and fatigue life of aluminum alloy castings

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate

MICROSTRUCTURE SIMULATION AND MECHANICAL PROPERTY PREDICTION OF MAGNESIUM ALLOY CASTING CONSIDERING SOLID SOLUTION AND AGING PROCESS

Advances in Multi-Scale Modeling of Solidification and Casting Processes

Microstructure evolution and mechanical properties of Al–Cu–Mn–Cd alloy fabricated by CMT-wire arc additive manufacturing

Modeling Microstructure and Yield Strength during Solidification and Heat Treatment Process in Al-7Si-Mg Cast Aluminum Alloys