Abstract:In the industry, chrome coating is an important player in the functional layer application. Due to its high corrosion and wear resistance as well as high hardness [1], hard chrome plating is a popular choice in the automotive and aerospace industry. However, since September 2017, the application of chrome (VI) in surface treatment is banned by the European Chemical Agency (ECHA) due to chrome (VI) being toxic and environmentally hazardous [2]. Chrome (III) compound is a popular substitute for chrome (VI) due to it being less toxic compared to chrome (VI). However, chrome (III) coating has a lower corrosion resistance, and the electroplating process is more sensitive to metallic impurities. Many new innovations have since been developed such as the plasma electrolytic oxidation (PEO), extreme highspeed laser deposition (EHLA). Even established technologies such as physical vapour deposition (PVD), thermal spraying and case hardening process have tried to replace hard chrome coating with a degree of success. Admittedly, the above-mentioned technologies have their fair share of disadvantages. PEO, a green procedure [3], causes a metal substrate to develop a highly resistant oxide which is extremely strong and corrosion as well as wear resistant. The process however needs a high temperature and pressure, continuous replacement of electrolytes and consumes a great amount of power which made the process not feasible for a wide industrial application [4-6]. EHLA and thermal spraying on the other hand are restricted to rotational symmetric components. PVD is restricted to substrates that can handle high processing temperature like nitrable ferrous base materials. Lastly, case hardening processes requires long heat treatments which contribute to a higher process cost. [7] In our presentation, another alternative for chrome coating based on electrodeposition will be introduced. The element tungsten is considered in our experiments because tungsten not only has an excellent corrosion properties and high tensile strength at high temperature, but it also has a microhardness of 650 Vickers. However, it is not possible to deposit tungsten from an aqueous solution because tungstate cannot be directly reduced to metallic tungsten due to a very low overvoltage for hydrogen evolution on tungsten. Thus, an induced co-deposition mechanism is needed, and it is known that tungsten can be easily codeposited with iron group metal. [8-9] In this study a modified Watt's bath is used as electrolyte to deposit NiW alloy. Our preliminary tests have shown that tungsten can also be deposited with nickel without the help of citric acid as complexing agent. The usage of citric acid does indeed inhibit the deposition of nickel but show no influence in the deposition of tungsten. Hence, in our study, experiments with the rotating disc electrode (RDE) will be done to see if tungsten content in the coating could be increased when the hydrodynamic and coating parameters are manipulated. The chemical composition of the layer is measured using SEM/EDX and the surface morphology is pictured using SEM. Metallographic cross-sections are made to see if there are any fissures in the layer and the hardness of the layer is measured using the microhardness test. The dependency of hardness on the tungsten content in the layer and the annealing parameter will also be shown in the presentation. XRD measurement is conducted for phase analysis and grain size calculation. Figure 1

The Development of the Electrochemical Deposition Process of Nickel-Diamond Coating with Phosphorus Modified DND

Effect of Nanodiamond Content in the Plating Solution on the Corrosion Resistance of Nickel–Nanodiamond Composite Coatings Prepared on Annealed 45 Carbon Steel

Synthesis and properties of electroless Ni–P–Nanometer Diamond composite coatings

Plasma-Sprayed Nanodiamond-Reinforced NiCrBSi Composite Coating for Improved Wear and Corrosion Resistance

Electrodeposition, microstructure and tribological performance of Ni/(N) incorporated diamond-like carbon films

Electrodeposition of Ni-W Alloy from Citric Acid Free Aqueous Electrolyte As a Substitute for Hard Chrome Coating and the Effect of Tungsten Content on Coating Hardness

A novel strategy for improving the wear resistance of electrodeposited Ni-diamond composite coatings by diamond surface morphology modification

Nanostructured Diamond Particles in the Development of Protective Anticorrosion Epoxy Coatings

Electrodeposition of Ni-W-P alloy

Electrochemical Corrosion Behavior of the Dlc Coated and Uncoated Niti Alloys

Modification of an Electroplated Nickel Interlayer Surface by Annealing Heat Treatment for Diamond Deposition on Tungsten Carbide

Surface nanocomposites prepared by electroless plating

Surface Characteristics and Electrochemical Corrosion Behavior of NiTi Coated with Diamond-Like Carbon

Electro-Brush Plating from Deep Eutectic Solvent: A Case of Nanocrystalline Ni Coatings with Superior Mechanical Property and Corrosion Resistance

Electrodeposition of Ni-P composite coatings: A review

Effect of Particle Concentration on the Microstructure and Properties of Electrodeposited Nickel–Diamond Composite Coatings

Electrodeposition of Ni-WC composite coatings: formation, structure and properties

Preparation and performance study of electroplated Ni–W/diamond ultrathin dicing blades

Microstructure and Corrosion Behavior of Plasma-Sprayed Nanodiamond-Reinforced NiAl Nanocomposite Coating

Synthesis of Ni nanoclusters supported on diamond by plasma technique and their electrochemical properties

Improved microhardness and wear resistance of the as-deposited electroless Ni–P coating