Abstract:Fatigue crack growth rate behavior in the threshold and near-threshold regimes for a Ti-6Al-4V solution-treated and over-aged (STOA) alloy was investigated using two test procedures: i ) accelerated load reduction (ALR) utilizing faster load-shed rates than recommended in the ASTM standard E647 load-reduction (LR) test procedure, and ii ) compression pre-cracking constant-amplitude (CPCA) or load-increasing (CPLI) and load-reduction (CPLR). Fatigue crack growth tests were conducted on compact, C(T), specimens (B = 6.35 mm) with two different widths ( W = 51 and 76 mm) at two stress ratios ( R = 0.1 and 0.7). The crack-growth-rate test data were compared to previous test data produced from the same batch of material using the ASTM LR and CPCA test procedures that were tested on C(T) specimens ( W = 25, 51 and 76 mm) over a wide range in stress ratios (R = 0.1, 0.4, and 0.7). Although none of the load-reduction test procedures provided a good representation of the threshold value (Δ K th ) at low R , the CPCA test procedure was the most promising. The LR, ALR, and CPLR test procedures were influenced by prior loading history, leading to higher Δ K th values and slower crack growth rates in the threshold regime due to a rise in the crack-opening loads. The LR and ALR tests at R = 0.1 and shed rates of −0.08, −0.32, and −0.95 mm −1 yielded Δ K th values that were 15 to 38 % higher than the estimated threshold stress-intensity factor range (Δ K * th ) R =0.1 based on the crack-closure model (FASTRAN). The compression pre–cracking test procedures are more accurate alternatives for developing threshold and near-threshold fatigue crack growth rates. Specifically, the CPLR test procedure produced a Δ K th value that was 8–18 % higher than (Δ K * th ) R =0.1 . Additionally, LR and ALR tests produced different Δ K th values as a function of the specimen width for a given load ratio, which violates classical fracture mechanics principles. In addition, the spread in the Δ K -rate data in the low-rate regime was larger than the spread in the mid-rate regime as a function of R , a term referred to as " fanning ". In contrast, the CPCA test procedure produced consistent crack growth rates over the same range of Δ K values examined, independent of the specimen width and these data did not exhibit " fanning " with R . Further research is necessary to develop standard test procedures capable of providing a more definitive representation of the Δ K th value in the threshold regime. However, FASTRAN can serve as a crucial tool in aligning the actual Δ K th values with those obtained through CP testing, thereby bridging the gap and enhancing the reliability of the results.

Determination of the Crack Tip Position by Digital Image Correlation during Static and Cyclic Fracture Toughness Tests of Aluminum Alloys

Instrumented indentation measurements of residual stresses around a crack tip under single tensile overloads

Depth-sensing Indentation Measurement and Finite Element Analysis of Residual Stress Field Near Fatigue Crack Tip

Crack Growth Patterns of Aluminum Tubular Specimens Subjected to Cyclic Tensile Loads

Identification and characterization of three-dimensional crack propagation mechanism in the Aluminium alloy AA2024-T3 using high-resolution Digital Image Correlation

METHOD OF ESTIMATING PLASTIC DEFORMATION DISTRIBUTIONS AT THE FATIGUE CRACK TIP BASED ON THE SOLUTION OF LINEAR ELASTICITY THEORY

Measurement and simulation of strain fields around crack tips under mixed-mode fatigue loading

Study on the behavior of small cracks in PA38-T6 (6060-T6) aluminum alloy under multiaxial fatigue loadings

Characterization of Surface Fatigue Crack Nucleation and Microstructurally Small Crack Growth in High Strength Aluminum Alloys

Estimation of Crack Tip Position in Adhesively Bonded Joints Subjected to Mode II Fatigue Loading

Deformation Fields Measurement of Crack Tip under High-Frequency Resonant Loading Using a Novel Hybrid Image Processing Method

Automatic Crack Tip Localization in Enormous DIC Images to In-Situ Characterize High-Temperature Fatigue Crack Growth Behavior

Fracture parameters analysis of compact tension specimens with deflected fatigue cracks: ZK60 magnesium alloy

An analysis of fatigue crack features at various crack lengths through mating fracture surface pairs

Statistical Analysis Methods of Fatigue Crack Growth Rate

Determination of Fatigue Failure Parameters from the Depth of Plastic Zones Beneath the Fracture Surface

An In Situ Study of Short Crack Initiation and Propagation During Fatigue Testing of a Hot Isostatically Pressed Al-7%Si-0.5%Mg (A357-T6) Alloy Specimen

Assessing fatigue crack growth thresholds for a Ti-6Al-4V (STOA) alloy using two experimental methods

Three-dimensional Quantitative in Situ Study of Crack Initiation and Propagation in AA 6061 Aluminum Alloy Sheets Via Synchrotron Laminography and Finite-Element Simulations

Study on Fracture Behavior of Nickel-Based Single Crystal Superalloy Subjected to High Temperature Fatigue Using Digital Image Correlation

Determination of Equivalent Crack Length for Voids in Metallic Alloys Based on Continuum Damage Mechanics Modeling